devolo Multi Node LAN 4TE

مواصفات المنتج

• نسخة برنامج ثابت: 7.16.5 أو أحدث
• الشركة المصنعة: ديفولو
• جهة الاتصال للدعم: الدعم@devolo.de

معلومات المنتج

MultiNode is a networking device that allows you to create a MultiNode network for seamless connectivity.

تعليمات استخدام المنتج

تثبيت:
Install and configure your MultiNode network following these steps:

1. Ensure your devices have firmware version 7.16.5 or newer.
2. Decide whether to provision the devices before or after electrical installation.
3. Run the setup wizard to begin the installation process.

إعدادات:
After installation, you can configure your MultiNode network settings using the setup wizard or the user manual available on the product webموقع.

استكشاف الأخطاء وإصلاحها والدعم:
If you encounter any issues or have feedback, please contact support at الدعم@devolo.de للحصول على المساعدة.

This quick start guide helps you install and configure your first MultiNode network.
ℹ This guide assumes that your devices have firmware version 7.16.5 or newer. If your devices run an older firmware version, consult the user manual available on the منتج webموقع.

ما تحتاجه

• A laptop with a LAN port
• كابل إيثرنت
• MultiNode LAN devices (at least two)
• Data sheet (technical specs, included in the package)

How MultiNode works

• MultiNode LAN 4TE is a DIN-rail device that uses powerline communication (PLC) to send data over low-voltagأنابيب البريد.
• Master node: The central controller of the network.
• Regular nodes: They connect to the master through PLC. A regular node can automatically switch to a repeater role if needed.
• عزل: Regular nodes talk only to the master, not to each other.
  Application devices (e.g., a charging station) connected to a regular node can only reach application devices connected to the master. Devices on different regular nodes cannot connect directly.
• The master node has a built-in web interface for setup and management; no extra tools are needed.

  

تعليمات خطوة بخطوة

1. خطط لشبكتك
   • Power supply considerations: Each power rail needs a circuit breaker. You can use one breaker for both the charging station and MultiNode, or separate breakers. MultiNode is powered by L1/N, e.g., from the charging infrastructure’s mains circuit.
   • مسافة: Large networks may need repeaters. The best range is up to 50 m per hop. 50–100 m may work, but over 100 m is not recommended.
   • الدوائر: One three-phase circuit for all devices gives the best results. Multiple circuits cause signal loss and noise. This can be solved with repeaters or by splitting networks via Ethernet.
   • الطوبولوجيا: The network self-organizes into a tree: the master node is at the root, with regular nodes automatically acting as repeaters when needed.
   • Master node placement: Place it where Ethernet is easy to reach, and signal paths are short. It is strongly recommended not to place it in the distribution unit.
   • Load management in EV charging scenarios: Since regular nodes connect only to the master, EV charging scenarios need careful upfront planning. For guidance, see the user manual on the منتج webموقع.
2. التركيبات الكهربائية
   • DIN-rail mounting and proper wiring must be carried out by a qualified electrician, in compliance with standards.
   • Connect the MultiNode devices to the mains.
   • It is recommended to record each device’s serial number, MAC address, and installation location (e.g., parking spot, floor number) to support maintenance.
     You can provision the devices either before or after electrical installation, depending on what works best for your workflow.
3. Connect your laptop
   Connect your laptop to the device you want to use as the master node, e.g., the device next to the Internet gateway, with an Ethernet cable. By default, all MultiNode LAN 4TE devices start as regular nodes.
4. افتح web واجهة.
   • افتح web المتصفح وادخل: http://devolo-xxxxx.local.
   • Replace xxxxx with the last 5 digits of the device’s serial number.
5. قم بتشغيل معالج الإعداد.

   
   

   عندما تفتح web interface of a factory-default device, it automatically redirects you to the setup wizard.
   • Click the button “Create a new network”. This sets the connected device as the master.

     

   • On the above screen, wait for all nodes to join the network, then click “Continue. On the next screen shown below, enter the settings and click “Save and apply to all nodes in the network”:

     

     • اسم نطاق باورلاين: Choose a clear name for the MultiNode network to help identify it.
     • Powerline password: Protects the powerline domain.
     • البذرة: A number from 0 to 59 that uniquely identifies a PLC network. It is recommended to leave this on automatic.
     • كلمة سر المشرف: Protects the MultiNode network management channel.
     • Web interface password: Protects access to the web واجهة.
   • After the configuration is applied to all nodes, you will be automatically redirected to the Overview, which lists all nodes in your MultiNode network as shown below. It is recommended to provide meaningful names to nodes, e.g., include a referencethe physicalical installation location.

     

يدعم

For questions or feedback, please contact us at الدعم@devolo.de.

التعليمات

Can I use MultiNode with older firmware versions?

MultiNode is designed to work best with firmware version 7.16.5 or newer for optimal performance and compatibility.

Do I need to configure each device individually in the network?

No, you can use the setup wizard to configure multiple devices simultaneously for easier network setup.

المستندات / الموارد

devolo Multi Node LAN 4TE [بي دي اف] دليل المستخدم 20251021, Multi Node LAN 4TE, Node LAN 4TE, LAN 4TE

مراجع

• دليل المستخدم