RGBlink NDI PTZ Camera Controller (RGBBKT) User Manual

1. المقدمة

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the RGBlink NDI PTZ Camera Controller (RGBBKT). This device is designed for professional video production environments, offering comprehensive control over various PTZ cameras using multiple protocols.

Image 1.1: RGBlink NDI PTZ Camera Controller (RGBBKT).

2. الإعداد

Follow these steps to set up your RGBlink NDI PTZ Camera Controller.

2.1 فك العبوة والفحص الأولي

• قم بإزالة جميع المكونات بعناية من العبوة.
• تأكد من وجود جميع العناصر المدرجة في قائمة التعبئة.
• Inspect the controller for any signs of physical damage. If damage is found, contact your dealer immediately.

2.2 توصيل وحدة التحكم

The RGBlink NDI PTZ Camera Controller supports various connection methods for power and camera control.

• الطاقة عبر إيثرنت (PoE): Connect a single RJ45 Ethernet cable from a PoE-enabled network switch to the controller's LAN port. This provides both power and network connectivity.
• محول طاقة خارجي: If PoE is not available, connect the provided power adapter to the DC 12V input port and to a power outlet.
• اتصالات الكاميرا:
  • Ethernet (IP Control): Connect PTZ cameras to the same network as the controller via RJ45 Ethernet cables. The controller supports VISCA over IP, ONVIF v2.42, and NDI v5.5 protocols.
  • التحكم التسلسلي: For cameras supporting serial communication, use RS232, RS422, or RS485 interfaces. Connect the appropriate cables from the controller's serial ports to the cameras.

Image 2.1: Rear panel connections including RS-232, RS-422, LAN (PoE), and Power Input.

الصورة 2.2: مثالample connection diagram showing PTZ Controller, PoE Switch, PTZ Cameras, Audio Mixer, and Computer.

Image 2.3: Diagram illustrating IP camera connections via a network switch.

2.3 تكوين الشبكة

For IP-based camera control, ensure the controller and cameras are on the same network segment. The controller supports automatic detection of NDI-enabled PTZ cameras.

• Access the controller's web واجهة عن طريق إدخال عنوان IP الخاص بها في ملف web browser. (Refer to the device's display or network tools to find the IP address).
• The default login credentials are typically 'admin' with a blank password. It is recommended to set a strong password immediately.
• ضمن web interface, configure camera protocols (e.g., ONVIF, VISCA over IP) and enter camera-specific user credentials if required.

Image 2.4: NDI|HX camera search and control interface on the controller.

3. التشغيل

This section details the operational functions of the RGBlink NDI PTZ Camera Controller.

3.1 أكثرview من الضوابط

The controller features a 3.49" LCD display, a 3D joystick, various knobs, and a numeric keypad for intuitive control.

Image 3.1: The controller's 3.49-inch LCD display.

الصورة 3.2: تفصيلية view of the 3D joystick and multi-function knobs.

Image 3.3: Layout of the controller's buttons and numeric keypad area.

3.2 اختيار الكاميرا

• أزرار الاختيار السريع: Use the dedicated CAM 1-5 buttons for quick selection of up to 5 cameras.
• المفاتيح العددية: For cameras beyond the quick select buttons (up to 255), press the معرف CAM button, then enter the camera number using the numeric keypad, and press يدخل.

Image 3.4: The controller's ability to manage multiple cameras.

3.3 التحكم PTZ

• عصا التحكم: The 3D joystick controls pan (left/right), tilt (up/down), and zoom (rotate the joystick).
• مقبض سرعة PT: Adjusts the gimbal movement speed for pan and tilt.
• Zoom Knob: Provides precise zoom control, especially useful in preview وضع.

3.4 Image Parameter Adjustment

• IRIS/SHUTTER Knob: Rotate to adjust aperture and shutter speed. Press to switch control modes.
• R/B GAIN Knob: Rotate to adjust red and blue gain. Press to switch control modes.
• FOCUS Button: اضغط على التركيز التلقائي button to switch the camera to auto focus mode.
• EXPOSURE Button: Cycles through exposure modes (Aperture Priority, Shutter Priority, Gain Priority, Manual Exposure, Auto Exposure).
• BACKLIGHT Button: Toggles the camera's backlight mode.
• WHITE BALANCE CYCLE Button: Cycles through white balance modes (Indoor, Outdoor, Manual, Auto).
• ONE PUSH TRIGGER Button: When white balance is set to "One-Push White Balance", press this button to initiate a one-push white balance calibration.

Image 3.5: Functions of buttons and knobs on the left side of the controller.

Image 3.6: Functions of buttons and knobs on the right side of the controller, including preset controls.

3.5 المسبقة

• SET PRESET Button: Press to enter preset position mode. Use the numeric keys to enter the preset number (0-9) and press يدخل للحفظ. يضعط خروج للخروج.
• CALL PRESET Button: Press to enter preset recall mode. Use the numeric keys to enter the preset number (0-9) and press يدخل to recall. Press خروج للخروج.
• The controller supports saving and recalling up to 255 presets per camera.

3.6 تصفح القائمة

• زر القائمة: Press to open or close the camera settings menu. In menu control mode, the joystick controls navigation (up, down, left, right), يدخل confirms selections, and خروج acts as a back button.

4. الصيانة

Proper maintenance ensures the longevity and optimal performance of your RGBlink NDI PTZ Camera Controller.

4.1 التنظيف

• Use a soft, dry cloth to clean the exterior of the controller.
• بالنسبة للأوساخ العنيدة، قم بإزالة الأوساخ برفق.ampبلل قطعة القماش بالماء أو بمحلول تنظيف خفيف غير كاشط.
• Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the surface and display.
• Ensure no liquids enter the device through openings or ports.

4.2 التخزين

• When not in use for extended periods, store the controller in a cool, dry place away from direct sunlight and extreme temperatures.
• حماية الجهاز من الغبار والرطوبة.

5. استكشاف الأخطاء وإصلاحها

يوفر هذا القسم حلولاً للمشكلات الشائعة التي قد تواجهها.

5.1 لا يوجد طاقة

• التحقق من مصدر الطاقة: تأكد من توصيل محول الطاقة بشكل آمن بكل من وحدة التحكم ومأخذ الطاقة العامل.
• فحص PoE: If using PoE, verify that the Ethernet cable is connected to a PoE-enabled port on your network switch and that the switch is powered on.
• سلامة الكابل: Inspect the power cable and Ethernet cable for any damage.

5.2 Cannot Control Camera

• الاتصال بالشبكة: For IP cameras, ensure the controller and cameras are on the same network and can communicate. Check network cables and IP addresses.
• عدم تطابق البروتوكول: Verify that the correct control protocol (e.g., VISCA over IP, ONVIF, NDI, Pelco-D/P) is selected on both the controller and the camera.
• معرف الكاميرا: Ensure the correct camera ID is selected on the controller.
• بيانات تسجيل الدخول: If the camera requires authentication, confirm that the correct username and password are configured in the controller's web واجهة.
• الاتصال التسلسلي: For serial control, check RS232/RS422/RS485 cable connections and ensure baud rates and addresses match between the controller and camera.
• البرامج الثابتة: Ensure both the controller and cameras have the latest firmware installed. Visit the RGBlink support webموقع للحصول على التحديثات.

5.3 LCD Display Issues

• لا يوجد عرض: تأكد من تشغيل وحدة التحكم.
• عرض قائمة: Check if there are any brightness settings on the controller that can be adjusted.

6. المواصفات

Image 6.1: Controller dimensions and typical usage environments.

Image 6.2: Visual representation of supported protocols including RJ45, RS485, RS422, RS232, ONVIF, NDI, Pelco-D, Pelco-P, and Visca.

7. عرض فيديو توضيحي للمنتج

Watch the official product video for a visual demonstration of the RGBlink NDI PTZ Camera Controller's features and operation.

8. الضمان والدعم

For warranty information, technical support, or service inquiries, please contact RGBlink customer service or visit their official webموقع.

• الشركة المصنعة: Xiamen RGBlink Science & Technology Co.,Ltd.
• رسمي Webموقع: www.rgblink.com (ملاحظة: هذا عنصر نائب URLيرجى الرجوع إلى عبوة المنتج أو الوثائق الرسمية للحصول على الدعم الصحيح. webموقع.)
• معلومات الاتصال: Refer to the RGBlink official website for the most current contact details for technical support and warranty claims.