1. المقدمة
The FLSUN S1 Pro is an advanced FDM Delta 3D printer designed for high-speed and high-precision additive manufacturing. It features an ultra-fast printing speed of up to 1200mm/s and an acceleration of 40,000mm/s², significantly reducing print times. Equipped with Klipper firmware, a 7-inch smart touch screen, and a 350℃ all-metal hotend, the S1 Pro supports a wide range of filaments, including high-performance engineering materials. Its large build volume of Φ320*320*430 mm³ accommodates substantial projects. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your FLSUN S1 Pro 3D Printer.
الصورة 1.1: الجبهة view of the FLSUN S1 Pro 3D Printer, showcasing its sleek design and enclosed build chamber.
2. ماذا يوجد في الصندوق
عند فتح العبوة، يرجى التأكد من وجود جميع المكونات:
- FLSUN S1 Pro 3D Printer (main unit)
- صندوق مجفف الخيوط
- كابل الطاقة
- كابل يو اس بي
- Tool Kit (various wrenches, screwdrivers, etc.)
- Sampلو خيوط
- دليل المستخدم (هذا المستند)
- دليل البدء السريع
Image 2.1: The FLSUN S1 Pro 3D Printer and its included accessories, demonstrating its 95% pre-assembled state.
3. تعليمات الإعداد
The FLSUN S1 Pro is designed for quick setup, being 95% pre-assembled. The initial setup typically takes less than 10 minutes.
- فك التعبئة: قم بإزالة الطابعة وجميع الملحقات من العبوة بعناية.
- الموقع: ضع الطابعة على سطح مستوٍ وثابت في منطقة جيدة التهوية.
- حَشد: Install the door and glass panels as per the instructions in the detailed دليل التثبيت (PDF).
- توصيل الطاقة: Connect the power cable to the printer and a suitable power outlet.
- التشغيل الأولي: Turn on the printer using the main power switch. The device will perform self-checks to ensure stability.
- التسوية التلقائية: The printer features automatic leveling. Follow the on-screen prompts on the 7-inch touch screen to initiate and complete the leveling process. This ensures optimal print bed calibration.
- تحميل الفتيل: Load your desired filament into the filament dryer box and then guide it into the extruder as instructed on the display.
- إتصال شبكة: Connect the printer to your local Wi-Fi network via the touch screen interface for remote monitoring and control.
للحصول على تعليمات مرئية مفصلة، يرجى الرجوع إلى الموقع الرسمي دليل التثبيت (PDF).
4. تعليمات التشغيل
4.1 واجهة المستخدم والتحكم
The FLSUN S1 Pro utilizes a 7-inch Klipper firmware smart touch screen for intuitive control. The visual operation interface allows for smart adjustment and monitoring directly from the printer. Additionally, with advanced Microtac radar control and Wi-Fi connectivity, you can monitor and control your printer in real-time from mobile phones and PCs.
Image 4.1: Remote control and monitoring capabilities via the FLSUN World app on a mobile device.
- جهاز التحكم عن بعد: Manage your printers remotely from anywhere.
- Tap it, Print it, Like it: Start printing tasks with a quick tap on the FLSUN World app, utilizing cloud storage for G-code files.
- Monitor in Pocket: Real-time checking of your printing progress.
- Smart Reminder: Receive notifications when print errors occur.
4.2 عملية الطباعة
- Prepare Model: Use compatible slicing software (FLSUN Slicer V2.0 or other slicers like PrusaSlicer, Cura) to prepare your 3D model. Ensure settings are optimized for the S1 Pro's capabilities, including its high speed and acceleration.
- تحويل File: انقل كود G المقسم file to the printer via USB or Wi-Fi (FLSUN World app).
- بدء الطباعة: حدد file on the touch screen or through the app and initiate the print.
- يراقب: Utilize the built-in camera for real-time monitoring and time-lapse recording. The printer's low noise level (55dB) ensures a quiet operating environment.
- Power-Off Resume: In case of power interruption, the printer supports power-off continuous printing, resuming from where it left off. Vibration compensation further ensures print quality.
Image 4.2: Illustration of the FLSUN S1 Pro's epic speed capabilities: 1200mm/s max printing speed, 40000mm/s² max acceleration, and 110mm³/s peak flow rate.
Image 4.3: Key features for smooth and consistent printing, including AI-powered functions, auto-leveling, spaghetti detection, and perfect first layer adhesion.
Image 4.4: Advanced features like the Air Filter, Filament Dryer, Built-in camera, Intelligent Zoned Heating, and 16GB EMMC storage.
5. الصيانة
Regular maintenance ensures the longevity and optimal performance of your FLSUN S1 Pro 3D Printer.
- تنظيف: Regularly clean the print bed, nozzle, and internal components to prevent debris buildup. Use a soft cloth and appropriate cleaning solutions.
- فلتر الهواء: The printer is equipped with a combined HEPA + activated carbon air filter. Check and replace the filter periodically as needed to maintain air quality and prevent odors.
- Filament Dryer Box: Ensure the filament dryer box is functioning correctly to keep your filament dry, which is crucial for print quality.
- فحص الفوهة: Periodically inspect the 0.4mm hardened steel nozzle for wear or clogs. Replace if necessary. The all-metal hot end can reach up to 350°C, supporting various high-temperature filaments.
- تشحيم: Refer to the detailed manual for any lubrication requirements for moving parts.
Image 5.1: Diagram illustrating the 350°C hotend, 50°C chamber, and 120°C hot bed for optimal material handling.
6. استكشاف الأخطاء وإصلاحها
يتناول هذا القسم المشكلات الشائعة التي قد تواجهها أثناء التشغيل.
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| Print Not Sticking to Bed | Improper bed leveling, dirty print surface, incorrect bed temperature. | Re-run auto-leveling. Clean the print surface with isopropyl alcohol. Adjust hot bed temperature according to filament type (Max 120°C). |
| Filament Clogging | Dust in filament, incorrect hotend temperature, worn nozzle, heat creep. | Ensure filament is dry (use filament dryer). Verify hotend temperature (Max 350°C). Clean or replace nozzle. Check cooling fan operation. |
| "Spaghetti" Prints | Poor bed adhesion, model detaching, extrusion issues. | The S1 Pro features كشف السباغيتي. Ensure proper bed adhesion. Monitor print progress via the built-in camera. |
| الطابعة لا تستجيب | Software glitch, loose connection, power issue. | Restart the printer. Check all cable connections. Ensure stable power supply. |
| جودة طباعة سيئة | Incorrect slicing settings, worn nozzle, vibration, wet filament. | Optimize slicing parameters. Replace nozzle if worn. The printer has تعويض الاهتزاز; ensure it's active. Use filament dryer. |
Image 6.1: Features like the 55dB quiet fan and Power Off Resume Print (UPS) contribute to a reliable printing experience.
7. المواصفات الفنية
| فئة | مواصفة | تفاصيل |
|---|---|---|
| عام | أقصى سرعة للطباعة | 1200 مم/ثانية |
| ماكس تسريع | 40000 مم/ثانية مربعة | |
| معدل التدفق الأقصى | 110 مم³/ثانية | |
| حجم البناء | Φ320*320*430 mm³ (Maximum height of the cylinder: 383mm) | |
| غرفة | مغلق | |
| مستوى الضوضاء | 55 ديسيبل | |
| رأس الأداة | فوهة | 0.4mm Hardened Steel Nozzle (supports various nozzle sizes) |
| Max Hot End Temp | 350 درجة مئوية | |
| قطر الخيط | 1.75 ملم | |
| خيط | خيوط مدعومة | Ideal: PLA, PETG, TPU. Satisfactory: ABS, ASA, PA, PC, PET. Capable: Carbon/Glass Fiber Reinforced PLA, PPS-CF, PPA-CF/GF. |
| Active Heating Dry Box | نعم | |
| كشف انسداد الفتيل | نعم | |
| Heatbed | لوحة البناء | لوحة PEI المزخرفة |
| Max Build Plate Temp | 120 درجة مئوية | |
| تدفئة المنطقة الذكية | Inner Circle Ø220mm, Outer Ring 220-320mm | |
| الالكترونيات | عرض | شاشة لمس ملونة مقاس 7 بوصة |
| تخزين | 16GB EMMC, 32GB USB Flash | |
| مزود الطاقة | 110-240 فولت، 50/60 هرتز | |
| استهلاك الطاقة في الوضع | 400 واط | |
| برمجة | ترقية البرامج الثابتة | OTA (عبر الأثير) |
| برنامج التقطيع | FLSUN Slicer V2.0, Other Slicers | |
| أنظمة التشغيل المدعومة | ماك أو إس، ويندوز | |
| سمات | كاميرا مراقبة | Realtime, Timelapse |
| كشف الخيوط | نعم | |
| تعويض الاهتزاز | نعم | |
| كشف الحطام | نعم | |
| كشف السباغيتي | نعم | |
| Screen Auto Sleep | نعم | |
| Printer Auto Power Off | نعم | |
| لصناعة السيارات في الإستواء | نعم | |
| استعادة فقدان الطاقة | Yes (Z lift, Backup Battery) | |
| فلتر الهواء | HEPA + Activated Carbon | |
| الأبعاد المادية | أبعاد المنتج (العمق × العرض × الارتفاع) | 23.62"D x 34.25"W x 9.45"H (600mm x 870mm x 240mm approx.) |
| Physical Dimension (Printer) | 550*596*1030 ملم | |
| وزن العنصر | 113 رطل (حوالي 51.2 كجم) | |
| لون | أسود |
Image 7.1: Comprehensive technical specifications for the FLSUN S1 Pro 3D Printer.
8. الضمان والدعم
FLSUN is committed to providing reliable products and excellent customer service.
- الإرجاعات: The product is eligible for 30-day easy returns. Please refer to the retailer's return policy for specific details.
- دعم العملاء: For technical assistance, troubleshooting, or warranty inquiries, please contact FLSUN Customer Support. You can often find support resources and contact information on the official FLSUN webالموقع أو من خلال بائع التجزئة الذي تم شراء المنتج منه.
- خطط الحماية: Extended protection plans, such as a 4-Year Protection Plan, may be available for purchase separately to provide additional coverage beyond the standard warranty.
- الموارد المتاحة على الإنترنت: قم بزيارة FLSUN Store on Amazon for additional product information, FAQs, and support.
