مقدمة
This manual provides essential instructions for the proper installation, operation, and maintenance of your YSIDO 60A Waterproof Brushed Electronic Speed Controller (ESC) with an XT60 plug. This ESC is designed for 1/10 scale RC cars, off-road trucks, and RC boats, compatible with 540 and 550 brushed motors. Please read this manual thoroughly before use to ensure optimal performance and safety.
معلومات السلامة
Always prioritize safety when operating RC equipment. Failure to follow safety guidelines can result in damage to the product, property, or personal injury.
- تأكد من أن جميع التوصيلات آمنة وصحيحة قبل تشغيل وحدة التحكم الإلكترونية في السرعة.
- Do not operate the ESC in conditions beyond its specified limits (e.g., voltagهـ، التيار، درجة الحرارة).
- Keep the ESC away from water and moisture unless specifically designed for waterproof operation. While this ESC is waterproof, ensure all other electronic components in your RC model are also protected.
- Disconnect the battery from the ESC when not in use to prevent accidental activation.
- Supervise children when they are operating RC models.
- Use only compatible batteries (2-3S LiPo or 5-9 cell NiMH) and motors (540/550 brushed).
محتويات الحزمة
تأكد من وجود جميع العناصر في الحزمة الخاصة بك:
- 1 x YSIDO 60A Brushed ESC (XT60 Plug)
سمات
- Waterproof and dustproof design.
- Compatible with 540 and 550 brushed motors.
- Suitable for 1/10 RC cars, off-road trucks, and RC boats.
- Strong resistant current capability.
- Excellent heat dissipation with integrated heatsink.
- Low internal resistance due to high current MOS transistors.
تحديد
| المعلمة | قيمة |
|---|---|
| نموذج | YS-60A-RTR |
| التيار المستمر | 60 أمبير |
| انفجار الحالي | 320 أمبير |
| حجم الإدخالtage | 2-3S ليبو / 5-9 خلايا NiMH |
| مخرج BEC | 6 فولت / 3 أمبير (وضع التبديل) |
| التوافق الحركي | 540/550 Brushed Motors |
| الأبعاد (الطول*العرض*الارتفاع) | 3.93 × 1.57 × 1.18 بوصة (100 × 40 × 30 مم) |
| وزن | 15.8 أونصة (448 جرام) |
الإعداد والتثبيت
Follow these steps for correct installation of the ESC into your RC model.
- تركيب وحدة التحكم الإلكترونية (ESC): Securely mount the ESC in your RC model using double-sided tape or screws, ensuring good airflow around the heatsink for optimal cooling.
- اتصال المحرك: Connect the two motor wires from the ESC to your brushed motor. The polarity (which wire goes to which motor terminal) can affect the motor's rotation direction. If the motor spins in the wrong direction, reverse the connections.
- اتصال جهاز الاستقبال: Plug the small three-wire cable (usually black, red, white) from the ESC into the throttle channel (CH2) of your RC receiver. This cable also supplies power to the receiver and steering servo (BEC output).
- توصيل البطارية: Connect your battery pack to the XT60 connector on the ESC. Ensure the polarity is correct (positive to positive, negative to negative).
Image: YSIDO 60A Brushed ESC with XT60 connector and wiring. This image displays the main unit of the ESC, showing the red heatsink, the XT60 battery connector, the motor output wires (red, blue, yellow), and the receiver connection cable.
الصورة: مفصلة view of YSIDO 60A ESC components. This image provides a comprehensive look at all the connected parts of the ESC, including the XT60 battery connector, the motor wires, the receiver plug, and the power switch, illustrating how they are integrated.
تعليمات التشغيل
Before operating your RC model, ensure the ESC is properly calibrated with your radio system.
- إعداد الارسال: Turn on your RC transmitter and ensure the throttle trim is set to neutral (center).
- ESC Power On: Connect the battery to the ESC. Turn on the ESC using its power switch.
- Calibration (if needed): Most ESCs automatically calibrate to the throttle range of your transmitter upon first power-up or after a reset. If your ESC does not respond correctly to throttle input, consult your radio system's manual for throttle calibration procedures. Typically, this involves holding full throttle on the transmitter, powering on the ESC, waiting for a beep, then moving to full brake, waiting for a beep, and finally returning to neutral.
- الاختبار الأولي: With the wheels off the ground, slowly apply throttle to ensure the motor spins correctly and in the desired direction. Adjust motor wire connections if the direction is incorrect.
البرمجة والإعدادات
The YSIDO 60A ESC features jumper pins for basic configuration. These pins allow you to select the operating mode and battery type.
Image: Close-up of YSIDO 60A ESC programming pins. This image shows the jumper pins on the ESC, labeled for selecting the operating mode (F/B, F/B/R, F/R) and battery type (LiPo, NiMH).
Use the provided jumper caps to select the desired settings:
- وضع التشغيل:
- F/B (Forward/Brake): For racing or applications where reverse is not needed.
- F/B/R (Forward/Brake/Reverse): Standard mode for general driving, allowing forward, brake, and reverse.
- F/R (للأمام/للخلف): For specific applications where braking is not required, only forward and reverse.
- نوع البطارية:
- ليبو: Select this for Lithium Polymer batteries. The ESC will automatically detect the cell count and set the low voltage cutoff protection.
- نيمه: Select this for Nickel-Metal Hydride batteries.
Ensure the ESC is powered off before changing jumper settings. After changing settings, power on the ESC to apply the new configuration.
صيانة
تساعد الصيانة الدورية على إطالة عمر وأداء وحدة التحكم الإلكترونية (ESC).
- تنظيف: Periodically clean the ESC to remove dirt, dust, and debris. Use a soft brush or compressed air. For waterproof ESCs, rinse with fresh water after use in wet conditions and allow to dry completely.
- التفتيشات: Regularly inspect all wires and connectors for signs of damage, fraying, or corrosion. Replace any damaged components immediately.
- إدارة الحرارة: Ensure the heatsink remains clear of obstructions to allow for efficient heat dissipation. Avoid operating the ESC in excessively hot environments.
Image: Close-up of the red aluminum heatsink on YSIDO 60A ESC. This image highlights the finned red aluminum heatsink, which is crucial for dissipating heat generated during operation and maintaining optimal ESC temperature.
استكشاف الأخطاء وإصلاحها
إذا واجهت مشاكل مع وحدة التحكم الإلكترونية (ESC)، فراجع المشاكل والحلول الشائعة التالية:
- المحرك لا يستجيب:
- Check all connections: battery, motor, and receiver.
- Ensure the transmitter is on and the battery is charged.
- Recalibrate the ESC throttle range.
- Verify the motor is not seized or damaged.
- المحرك يعمل في الاتجاه الخاطئ:
- Reverse the two motor wire connections between the ESC and the motor.
- ارتفاع درجة حرارة وحدة التحكم الإلكترونية:
- Ensure adequate airflow around the ESC heatsink.
- Check if the motor is too large or geared too high for the application, causing excessive load.
- تحقق من حجم البطاريةtagيقع ضمن النطاق المحدد.
- عملية متقطعة:
- تحقق من وجود توصيلات فضفاضة أو أسلاك تالفة.
- تأكد من أن البطارية مشحونة بالكامل وفي حالة جيدة.
- Check for radio interference.
الضمان والدعم
YSIDO products are manufactured to high-quality standards. For warranty information or technical support, please refer to the retailer where you purchased this product or visit the official YSIDO webموقع للحصول على تفاصيل الاتصال.
