Cube Acid Pro 80 Bicycle Lighting Set

1. المقدمة

Thank you for choosing the Cube Acid Pro 80 Bicycle Lighting Set. This set, comprising the Acid Pro 80 front light and the Acid Pro rear light, is designed to enhance your visibility and safety during cycling. Both lights are StVZO approved, ensuring compliance with German road traffic regulations, and are splash-proof for reliable performance in various weather conditions. The integrated rechargeable batteries offer convenience, and the tool-free mounting system allows for quick and easy installation.

2. محتويات العبوة

يرجى التأكد من وجود جميع العناصر في الحزمة الخاصة بك:

• Acid Pro 80 Front Light
• Acid Pro Rear Light
• كابل شحن ميكرو يو اس بي

Image: The complete Cube Acid Pro 80 Bicycle Lighting Set, featuring the front and rear lights.

3. الإعداد والتثبيت

3.1. Front Light Installation

The Acid Pro 80 front light features an asymmetrical design and a rod holder with a Slide-Lock attachment system, allowing for central positioning on your handlebars for a clean look. The silicone strap ensures a secure, tool-free mount.

1. Open the silicone strap on the front light's mounting bracket.
2. Position the light centrally on your bicycle handlebars.
3. Wrap the silicone strap around the handlebar and secure it to the hook on the bracket. Ensure the light is firmly attached and does not wobble.
4. Adjust the angle of the light to illuminate the road ahead effectively, without dazzling oncoming traffic.

الصورة: الجانب view of the Acid Pro 80 front light securely mounted on bicycle handlebars.

الصورة: أعلى view of the Acid Pro 80 front light, demonstrating its central mounting position on the handlebars.

3.2. Rear Light Installation

The Acid Pro rear light also uses a flexible silicone strap for easy and tool-free attachment to your seat post or other suitable bicycle frame parts.

1. Open the silicone strap on the rear light.
2. Place the light on your bicycle's seat post, ensuring it faces directly backward.
3. Wrap the silicone strap around the seat post and secure it to the hook on the light. Ensure it is tight and stable.

Image: Close-up of the Acid Pro rear light, highlighting its red lens and reflector design.

4. التشغيل

4.1. Charging the Lights

Both the front and rear lights are rechargeable via the included micro USB cable. It is recommended to fully charge the lights before first use.

• Locate the micro USB port on each light. For the rear light, it is typically on the side or bottom, protected by a rubber flap.
• Connect the micro USB cable to the light's port and the other end to a USB power source (e.g., computer USB port, USB wall adapter).
• An indicator light (usually red during charging, green when fully charged) will show the charging status.
• Charging time may vary, but typically takes a few hours for a full charge.

Image: Close-up of the Acid Pro rear light, showing the micro USB charging port with its protective cover.

4.2. تشغيل/إيقاف

Each light has a power button, usually located on the top or side.

• لتشغيل الضوء ONاضغط مع الاستمرار على زر التشغيل لمدة ثانية أو ثانيتين تقريبًا.
• لتشغيل الضوء عن, press and hold the power button again for approximately 1-2 seconds.
• Some models may have multiple light modes (e.g., steady, flashing). Briefly press the power button to cycle through available modes.

5. الصيانة

Proper maintenance will extend the lifespan of your lighting set:

• تنظيف: Wipe the lights with a soft, damp قماش. لا تستخدم المنظفات الكاشطة أو المذيبات، لأنها قد تتلف القماش.asing or lens.
• العناية بالبطارية: Recharge the batteries regularly, even if the lights are not used frequently, to maintain battery health. Avoid completely draining the battery before recharging.
• تخزين: Store the lights in a cool, dry place when not in use. If storing for an extended period, ensure the batteries are partially charged (around 50%) to prevent deep discharge.
• مقاومة الماء: While splash-proof (IP44 rated), avoid submerging the lights in water. Ensure the USB port cover is securely closed to maintain water resistance.

6. استكشاف الأخطاء وإصلاحها

If you encounter issues with your lighting set, try the following:

• الضوء لا يضيء: تأكد من شحن البطارية. قم بتوصيل المصباح بمصدر طاقة USB وتحقق من مؤشر الشحن.
• الضوء خافت: قد تكون البطارية منخفضة. أعد شحن المصباح بالكامل.
• ومضات الضوء: Check the mounting to ensure it is secure. If the issue persists, recharge the battery.
• مشكلة الشحن: Try a different micro USB cable or USB power source. Ensure the cable is fully inserted into the port.

If these steps do not resolve the issue, please contact Cube customer support or your retailer for further assistance.

7. المواصفات

8. الضمان والدعم

For warranty information and customer support, please refer to the documentation provided with your purchase or visit the official Cube webالموقع. احتفظ بإثبات الشراء الخاص بك لاستخدامه في أي مطالبات بالضمان.