دليل مستخدم إشارات الانعطاف LED للدراجات النارية والسكوتر من ماد مارس بجهد 12 فولت

1. المقدمة

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Mad Mars 12V LED Motorcycle Scooter Turn Signals. Please read this manual thoroughly before installation and keep it for future reference.

2. معلومات السلامة

• السلامة الكهربائية: افصل دائمًا بطارية السيارة قبل القيام بأي عمل كهربائي لتجنب حدوث ماس كهربائي أو صدمة كهربائية.
• التثبيت الاحترافي: If you are not familiar with motorcycle or scooter electrical systems, it is highly recommended to have these turn signals installed by a qualified professional.
• المجلدtagالتوافق ه: These turn signals are designed for 12V DC systems only. Do not connect to higher voltagالأنظمة الإلكترونية.
• التثبيت الآمن: Ensure the turn signals are securely mounted to prevent detachment during vehicle operation.
• CE Homologation: These turn signals are CE approved, indicating compliance with European safety standards.

3. محتويات العبوة

• One (1) Pair of Mad Mars 12V LED Motorcycle Scooter Turn Signals (Orange)

4. المواصفات

5. الإعداد والتثبيت

Follow these steps carefully for proper installation. Professional installation is recommended.

1. تجهيز السيارة: تأكد من إيقاف تشغيل محرك السيارة وفصل البطارية لمنع حدوث مخاطر كهربائية.
2. Remove Old Turn Signals: Carefully remove the existing turn signals from your motorcycle or scooter. Note the wiring connections.
3. Mount New Turn Signals: Insert the threaded bolt of the Mad Mars turn signal into the mounting hole. Secure it with the provided nut, ensuring it is tight but not overtightened. The thread diameter is 8mm.

Image 1: Mad Mars 12V LED Turn Signals. This image shows a pair of orange LED turn signals with their wiring and mounting hardware.

4. اتصال الأسلاك:
   • Identify the positive wire of the Mad Mars turn signal (typically yellow or red) and the negative/ground wire (typically black).
   • Connect the positive wire of the turn signal to the vehicle's positive turn signal wire.
   • Connect the negative wire of the turn signal to the vehicle's negative or ground wire.
   • Use appropriate electrical connectors (not included) and ensure all connections are secure and insulated to prevent short circuits.
5. Repeat for Second Turn Signal: Follow the same steps for the other turn signal.
6. أعد توصيل البطارية واختبارها: Reconnect the vehicle's battery. Turn on the ignition and test both turn signals to ensure they flash correctly. If they do not flash or flash too quickly/slowly, you may need a load resistor or an LED flasher relay (not included).

Image 2: Mad Mars 12V LED Turn Signals (Alternate View). This image provides another view of the orange LED turn signals, highlighting their compact design.

6. تعليمات التشغيل

Once properly installed, the Mad Mars 12V LED Turn Signals operate in conjunction with your motorcycle or scooter's existing turn signal switch. Activate the left or right turn signal switch as you normally would to indicate a turn or lane change. The LED lights will flash to provide clear visibility to other road users.

7. الصيانة

• تنظيف: Clean the turn signal lenses periodically with a soft, damp قطعة قماش. تجنب استخدام المنظفات الكاشطة أو المذيبات التي قد تتلف البلاستيك.
• تقتيش: Regularly check the mounting bolts for tightness and inspect the wiring for any signs of wear, fraying, or corrosion. Ensure the connections remain secure.
• عمر الصمام: LED lights have a long lifespan and typically do not require replacement under normal operating conditions.

8. استكشاف الأخطاء وإصلاحها

• Turn Signals Not Lighting Up:
  • Check all wiring connections for proper contact and insulation.
  • Verify that the vehicle's battery is charged and providing 12V power.
  • Inspect the vehicle's turn signal fuse.
• Turn Signals Flashing Too Fast (Hyper-flashing):
  • LED turn signals draw less power than traditional incandescent bulbs, which can cause the vehicle's flasher relay to interpret a bulb outage, resulting in hyper-flashing.
  • This can typically be resolved by installing a load resistor (not included) in parallel with each LED turn signal or by replacing the stock flasher relay with an LED-compatible flasher relay (not included).
• Turn Signals Not Flashing (Solid On):
  • This can also be caused by incompatibility with the vehicle's flasher relay. Consider installing a load resistor or an LED-compatible flasher relay.

9. الضمان والدعم

للحصول على معلومات الضمان أو الدعم الفني، يرجى الرجوع إلى وثائق الشراء أو الاتصال بالبائع مباشرةً. احتفظ بإثبات الشراء لتقديم أي مطالبات ضمان.