Tackform Enduro Series 3.5-inch Aluminum Dual Articulating Arm

1. انتهى المنتجview

The Tackform Enduro Series 3.5-inch Aluminum Dual Articulating Arm is designed for versatile device mounting. It features dual articulating 20mm ball sockets and thumbscrews for quick and precise adjustments. This arm is a core component of the Tackform Enduro Series, an ecosystem of mounting solutions.

• التوافق: Fully compatible with all Tackform Enduro Series 20mm components, including suction cups, table clamps, headrest clamps, and various device holders (phones, tablets, action cameras).
• بناء: Constructed entirely from aluminum for durability and strength. Thumbscrews are made of ABS Plastic.
• طول: Total arm length is 3.5 inches.
• التعبير: Dual ball and socket joints provide multiple points of articulation for optimal device positioning.
• التنوع: Can be used to replace existing arms for different lengths or to add articulation points with ball-to-ball adapters.

2. المكونات

The Tackform Dual Articulating Arm consists of a central aluminum arm with two 20mm ball sockets at each end. Each socket is secured by a thumbscrew for independent adjustment.

Figure 1: The Tackform 3.5-inch Aluminum Dual Articulating Arm.

Figure 2: The 3.5-inch length of the articulating arm.

Figure 3: The arm is compatible with 20mm Enduro Series components.

3. الإعداد والتثبيت

To set up your Tackform Dual Articulating Arm, follow these steps:

1. Loosen Thumbscrews: Gently loosen the thumbscrews on both ends of the arm to allow the ball sockets to open.
2. Insert Ball Mounts: Insert your desired 20mm ball mounts (e.g., a base mount and a device holder) into each socket. Ensure the balls are fully seated within the sockets.
3. Tighten Thumbscrews: Hand-tighten the thumbscrews to secure the ball mounts. Do not overtighten.
4. ضبط الموقف: Loosen one thumbscrew slightly to adjust the angle of that specific ball joint. Once the desired angle is achieved, re-tighten the thumbscrew. Repeat for the other joint if necessary.

For a visual guide on attaching and securing the arm, please refer to the official product overview الفيديو أدناه.

Additional demonstrations of 20mm ball arm functionality can be seen in the following videos:

4. التشغيل

The dual articulating design allows for flexible positioning of your mounted device. Each thumbscrew independently controls the tightness of its respective ball socket, enabling precise adjustments without affecting the other joint.

Figure 4: The arm allows for 180-degree rotation at each joint.

Figure 5: The ball joints enable full 360-degree rotation for optimal viewزوايا متعددة.

To adjust the arm:

1. تخفيف: Turn the desired thumbscrew counter-clockwise to loosen the grip on the ball.
2. موضع: Adjust the angle and orientation of the attached device or base.
3. يؤمن: Turn the thumbscrew clockwise to tighten and secure the ball in its new position. Ensure it is firm to prevent movement during use.

Figure 6: The arm can be used in various configurations, such as mounting an action camera or a tablet.

5. الصيانة

To ensure the longevity and optimal performance of your Tackform Dual Articulating Arm, consider the following maintenance tips:

• تنظيف: Wipe the aluminum arm and ABS plastic thumbscrews with a soft, damp استخدم قطعة قماش لإزالة الغبار والأوساخ. تجنب استخدام المنظفات الكاشطة أو المذيبات التي قد تتلف السطح.
• تقتيش: Periodically inspect the arm and thumbscrews for any signs of wear, damage, or loosening.
• ضيق: Ensure all thumbscrews are adequately tightened before each use to prevent accidental movement or detachment of your device.

6. استكشاف الأخطاء وإصلاحها

If you encounter any issues with your Tackform Dual Articulating Arm, please consider the following:

• الذراع لا تثبت في الوضعية: Ensure both thumbscrews are fully tightened. If using a rubberized ball, confirm it is properly seated within the socket.
• صعوبة التأقلم: Loosen the thumbscrews sufficiently to allow free movement of the ball joints. If the arm is new, it may require a few adjustments to loosen up.
• مشاكل التوافق: Verify that all connected components are 20mm ball compatible. This arm is specifically designed for 20mm ball systems.

7. المواصفات

8. الضمان والدعم

This product is manufactured by Tackform. For any warranty claims, technical support, or product inquiries, please contact Tackform directly through their official customer service channels. Refer to the product packaging or the Tackform webالموقع للحصول على أحدث معلومات الاتصال.