دليل مستخدم محلل الهوائي RigExpert Stick 230

1. المقدمة

The RigExpert Stick 230 is a compact, portable antenna analyzer designed for precise measurement of cable and antenna system parameters. It operates within a frequency range of 100 kHz to 230 MHz, making it suitable for various radio communication applications.

1.1 الميزات الرئيسية

• Measures SWR (Standing Wave Ratio), return loss, R, X, Z, L, C, Magnitude, and Phase Angle.
• Frequency range: 0.1 to 230 MHz with 1 KHz resolution.
• Supports 25, 50, 75, 100, 150, 200, 300, 450, and 600-Ohm systems.
• Multiple display modes including SWR chart, fixed HAM bands, and Multé mode.
• Equipped with a 200x200 monochrome e-paper display for clear visibility.
• UHF (SO-239) connector for antenna connection.
• Powered by a 3.7V Li-Ion 18650 battery or via USB.

1.2 الاستخدام المقصود

This analyzer facilitates:

• Rapid assessment of antenna performance in various environments.
• Precise tuning of antennas to their resonant frequency.
• Comparative analysis of antenna characteristics over time.
• Measurement of capacitance or inductance for reactive loads.

2. معلومات السلامة

يرجى مراعاة احتياطات السلامة التالية لمنع تلف الجهاز أو الإصابة الشخصية:

• لا تعرض الجهاز لدرجات حرارة قصوى أو رطوبة أو أشعة الشمس المباشرة لفترات طويلة.
• Use only the specified battery type (3.7V Li-Ion 18650) and charging methods.
• Avoid disassembling the device. Refer servicing to qualified personnel.
• Ensure proper connection of antennas and cables to prevent damage to the analyzer's RF port.

3. محتويات العبوة

تأكد من وجود جميع العناصر في العبوة:

• RigExpert Stick 230 Antenna Analyzer
• كابل يو اس بي
• حزام المعصم
• دليل البدء السريع

Image 3.1: The RigExpert Stick 230 Antenna Analyzer package contents, including the analyzer unit, USB cable, wrist strap, and quick start guide.

4. انتهى الجهازview

Familiarize yourself with the components of the RigExpert Stick 230.

الصورة 4.1: الجبهة view of the RigExpert Stick 230, highlighting the e-paper display and the 2x3 control keypad.

4.1 العرض

The device features a 200x200 monochrome e-paper display, providing clear readings even in bright conditions.

4.2 أزرار تحكم

The 2x3 keypad includes navigation buttons (up, down, left, right), an Enter button, and a Power button for device operation.

4.3 الموصلات

• موصل RF: UHF (SO-239) type, located at the top of the device, for connecting antennas or test loads.
• منفذ USB: Located at the bottom, used for charging the internal battery and connecting to a personal computer for data transfer or firmware updates.

5. الإعداد

5.1 شحن البطارية

1. Connect the supplied USB cable to the analyzer's USB port.
2. Connect the other end of the USB cable to a powered USB port on a computer or a USB wall adapter.
3. The device will indicate charging status on the display. A full charge typically takes several hours.

The analyzer can also draw power directly from the USB source when connected.

5.2 التشغيل المبدئي

1. Press and hold the Power button until the display activates.
2. The device will boot up and display the main menu or the last used measurement screen.

6. تعليمات التشغيل

6.1 Basic Antenna Measurement

1. Ensure the analyzer is adequately charged or connected to a power source.
2. Connect the antenna to be tested to the UHF (SO-239) connector on the analyzer. Ensure the connection is secure.
3. قم بتشغيل الجهاز.
4. Navigate through the menu using the control buttons to select the desired measurement mode (e.g., SWR, Single Frequency).
5. Enter the desired frequency using the navigation buttons. The frequency can be adjusted with 1 KHz resolution.
6. The display will show the measured parameters, such as SWR, return loss, R, and X.

6.2 طرق العرض

The RigExpert Stick 230 offers several display modes:

• Single Frequency: Displays SWR, return loss, R, X, Z, L, C, Magnitude, and Phase Angle at a specific frequency.
• مخطط SWR: Plots SWR over a frequency range with 100 data points.
• HAM Bands Chart: Provides SWR charts specifically for IARU Region HAM bands.
• Multé Mode: Designed for quick checks of multiband antennas.

6.3 System Impedance Selection

The analyzer supports measurements for various system impedances. Access the settings menu to select the appropriate impedance (25, 50, 75, 100, 150, 200, 300, 450, or 600 Ohms) for your application.

6.4 اتصال الكمبيوتر

Connect the analyzer to a personal computer via the USB port to:

• Transfer measurement data.
• تحديث البرامج الثابتة للجهاز.
• Utilize companion software (if available from RigExpert) for advanced analysis.

7. الصيانة

7.1 التنظيف

Wipe the device with a soft, dry cloth. Do not use liquid cleaners or solvents, as they may damage the display or casing.

7.2 التخزين

Store the analyzer in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, ensure the battery is partially charged (around 50%) to prolong its lifespan.

7.3 العناية بالبطارية

The internal Li-Ion battery is designed for long life. To maximize battery health:

• تجنب تفريغ البطارية بالكامل بشكل متكرر.
• Charge the battery regularly, even if the device is not in frequent use.
• Do not expose the device to temperatures above 60°C (140°F) or below -20°C (-4°F).

8. استكشاف الأخطاء وإصلاحها

8.1 الجهاز لا يعمل

• Ensure the battery is charged. Connect the device to a USB power source and attempt to power it on.
• Verify that the Power button is pressed and held sufficiently.

8.2 قراءات القياس غير الصحيحة

• Check all cable connections to ensure they are secure and free from damage.
• Verify that the correct system impedance is selected in the device settings.
• Ensure the antenna or load being tested is properly connected and functioning.

8.3 مشاكل العرض

• If the display is unresponsive or shows artifacts, try restarting the device.
• Ensure the device is not exposed to extreme cold, which can temporarily affect e-paper display performance.

9. المواصفات

10. الضمان والدعم

For warranty information and technical support, please refer to the official RigExpert webالموقع أو تواصل مع الوكيل المعتمد. احتفظ بإيصال الشراء لطلبات الضمان.