Maxxima LED Slide Dimmer Switch User Manual

1. المقدمة

Thank you for choosing the Maxxima LED Slide Dimmer Switch. This product is designed to provide smooth and reliable dimming for a variety of lighting loads, including incandescent, dimmable LED, and CFL bulbs. It supports both single pole and 3-way circuit configurations, offering flexibility for your lighting control needs. Please read this manual thoroughly before installation and use to ensure proper operation and safety.

2. معلومات السلامة

تحذير: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring! This device must be installed in accordance with all national and local electrical codes.

• للاستخدام الداخلي فقط.
• Do not use with non-dimmable lighting fixtures.
• Not for use with ceiling fans or motor loads.
• تأكد من إجمالي واتtage of connected bulbs does not exceed the dimmer's maximum rating (600W Incandescent; 200W Dimmable LED/CFL).
• إذا لم تكن متأكدًا من أي جزء من هذه التعليمات ، فاستشر كهربائيًا مؤهلًا.

3. محتويات العبوة

• Maxxima LED Slide Dimmer Switch (Model: MEW-DM650)
• لوحة الحائط اللولبية
• مسامير التثبيت
• صواميل الأسلاك

4. الإعداد والتثبيت

This dimmer switch is compatible with both single pole and 3-way wiring configurations. In a 3-way circuit, only one dimmer may be used; the second switch must be an ON/OFF only switch.

4.1 مخطط الأسلاك

Refer to the following image for typical wiring connections. Always ensure power is OFF before beginning any wiring.

4.2 خطوات التثبيت

1. إيقاف تشغيل الطاقة: At the circuit breaker or fuse box, turn off the power to the switch location. Verify power is off using a voltagه اختبار.
2. إزالة المفتاح القديم: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch.
3. تحديد الأسلاك: Identify the LINE (hot), LOAD, and GROUND wires. For 3-way installations, also identify the TRAVELER wires.
4. توصيل الأسلاك: Connect the wires from the wall box to the dimmer switch using the provided wire nuts.
   • Black wire on dimmer: Connect to LINE (hot) wire.
   • Red wire(s) on dimmer: Connect to LOAD wire (and TRAVELER wire for 3-way).
   • Green wire on dimmer: Connect to GROUND wire.
5. Mount Dimmer: Carefully push the wired dimmer switch into the wall box. Secure it with the provided mounting screws.
6. تثبيت لوحة الحائط: Snap the screwless wall plate onto the dimmer switch.
7. اعادة الطاقة: قم بإعادة تشغيل الطاقة من قاطع الدائرة.

4.3 Sensitivity Adjustment (Trim Dial)

The dimmer features a trim dial located underneath the cover plate. This dial allows you to adjust the low-end dimming range to ensure optimal compatibility with various LED and CFL lamps, preventing flicker or premature turn-off at low light levels.

To adjust: Remove the screwless wall plate. Locate the small trim dial at the bottom of the dimmer. Turn the dial clockwise to increase the minimum light level or counter-clockwise to decrease it, until stable dimming is achieved without flicker.

5. تعليمات التشغيل

The Maxxima LED Slide Dimmer Switch features a vertical slide control for dimming and a separate ON/OFF button.

• تشغيل / ايقاف: Press the bottom button to turn the lights ON or OFF.
• يعتم: Move the vertical slide control up to increase light brightness and down to decrease light brightness.

6. الصيانة

The Maxxima LED Slide Dimmer Switch requires minimal maintenance. To clean, simply wipe the surface with a soft, damp قطعة قماش. لا تستخدم المنظفات الكاشطة أو المذيبات، لأنها قد تتلف الطبقة الخارجية.

7. استكشاف الأخطاء وإصلاحها

• Lights flicker or do not dim properly: Adjust the sensitivity trim dial (refer to Section 4.3). Ensure your bulbs are dimmable LED or CFL, or incandescent.
• الأضواء لا تضاء: Check the circuit breaker. Verify all wiring connections are secure. Ensure the dimmer is not connected to a non-dimmable fixture.
• Dimmer does not work with low wattage LED loads: The dimmer may not be compatible with LED loads of 4.5 watts or less. Consider increasing the total wattage of connected LED bulbs.
• Dimmer gets warm: It is normal for dimmers to feel warm during operation. If it becomes excessively hot or emits a burning smell, immediately turn off power at the circuit breaker and consult a qualified electrician.
• Not for use with ceiling fans: This dimmer is designed for lighting loads only and should not be used to control ceiling fans or other motor-driven appliances.

8. المواصفات

9. الضمان والدعم

The Maxxima LED Slide Dimmer Switch comes with a ضمان لمدة 1 سنوات from the date of purchase, ensuring safety and reliability. This warranty covers defects in materials and workmanship under normal use.

For technical support, troubleshooting assistance, or warranty claims, please contact Maxxima customer service. Refer to the product packaging or the Maxxima webالموقع للحصول على أحدث معلومات الاتصال.