دليل مستخدم خوذة الدراجة الهوائية شينماكس HT-19

مقدمة

This manual provides essential instructions for the proper use, adjustment, and maintenance of your Shinmax HT-19 Bicycle Helmet. Please read this manual thoroughly before using the helmet to ensure your safety and the longevity of the product. This helmet is designed for cycling activities and offers enhanced protection with its durable construction, integrated LED taillight, and magnetic visor.

معلومات السلامة

• Always wear your helmet when cycling.
• Ensure the helmet fits snugly and is properly secured with the chin strap.
• A helmet cannot protect against all possible impacts. It is designed to reduce the risk of head injury in certain types of accidents.
• Inspect your helmet regularly for any signs of damage. If the helmet has sustained an impact, even if no visible damage is present, it should be replaced immediately.
• Do not modify the helmet or use solvents, paints, or adhesives on it, as this may compromise its protective capabilities.
• This helmet is intended for cycling use only.

محتويات الحزمة

عند فتح العبوة، تأكد من وجود جميع المكونات التالية:

• 1 x Shinmax HT-19 Bicycle Helmet
• 1 x Magnetic Visor (Goggles)
• 1 x Integrated LED Taillight
• Spare Batteries for LED Taillight
• 1 x Helmet Storage Bag (may vary by package)

يثبت

1. Helmet Fit Adjustment

Proper helmet fit is crucial for safety. The helmet should sit level on your head, covering your forehead, and should not tilt forward or backward.

1. التمركز: Place the helmet on your head so it covers your forehead. The front edge should be approximately 1.5 cm (about one finger's width) above your eyebrows.
2. Rear Adjustment Dial: Locate the adjustable dial at the back of the helmet. Rotate the dial clockwise to tighten the internal retention system, or counter-clockwise to loosen it. Adjust until the helmet feels snug but comfortable, without excessive pressure points.
3. Side Straps: Adjust the side straps so they form a "V" shape just below your ears. The strap dividers should be positioned comfortably.
4. الذقن حزام: Fasten the quick-release buckle under your chin. Tighten the chin strap until it is snug. You should be able to open your mouth wide, but the helmet should not move more than an inch in any direction.
5. التحقق النهائي: Shake your head gently. The helmet should not shift significantly. If it does, readjust the dial and straps.

Figure 1: This image illustrates the key components for helmet adjustment: the adjustable dial at the back for head circumference, the quick-release buckle on the chin strap, and the removable internal padding for comfort and hygiene.

Figure 2: To ensure a correct fit, measure your head circumference approximately 1.5 cm (half an inch) above your ears, as shown in this diagram. This measurement helps determine the appropriate helmet size.

2. Magnetic Visor Installation

The Shinmax HT-19 helmet includes a magnetic visor for eye protection against wind, sun, and debris.

1. مرفق: Align the magnets on the visor with the corresponding magnetic points on the helmet's front edge. The visor will snap into place securely.
2. تعديل: The visor can be easily flipped up or removed with one hand when not needed.

Figure 3: The magnetic visor easily attaches to the helmet's front using integrated magnets. This image shows the visor both separated from the helmet and securely fastened in place.

Figure 4: The magnetic visor offers versatility: it can be completely removed, flipped upwards when not needed, or lowered to provide eye protection during cycling.

3. LED Taillight Operation

The integrated LED taillight enhances visibility, especially in low-light conditions.

1. تركيب البطارية: The taillight typically comes with batteries pre-installed or included separately. If installing, open the battery compartment (usually a small screw or clip on the back of the light) and insert the provided CR1632 lithium-ion batteries, ensuring correct polarity.
2. تشغيل الطاقة/اختيار الوضع: Press the button on the LED taillight to cycle through its three modes:
   • ضوء ثابت
   • وميض بطيء
   • وميض سريع
3. إيقاف التشغيل: Continue pressing the button until the light turns off.

Figure 5: The helmet features an integrated LED taillight at the rear, offering three distinct lighting modes—constant, slow flashing, and fast flashing—to enhance visibility for cyclists.

تعليمات التشغيل

Once the helmet is properly adjusted and the visor and taillight are set up, you are ready to use your Shinmax HT-19 helmet.

• ارتداء الخوذة: Always ensure the helmet is worn correctly, level on your head, and securely fastened before starting your ride.
• Using the Visor: Attach the magnetic visor when you need eye protection. Flip it up or remove it if conditions do not require it or for better airflow.
• Activating the Taillight: Turn on the LED taillight, especially during dawn, dusk, night, or in low-visibility conditions, to increase your presence to other road users. Select the flashing mode for maximum attention.

صيانة

Cleaning the Helmet

• Use only mild soap and water to clean the helmet shell and padding.
• Do not use harsh chemicals, solvents, or abrasive cleaners, as these can damage the helmet's materials and compromise its protective integrity.
• The internal padding is removable for washing. Hand wash with mild soap and air dry completely before reinserting.

Cleaning the Visor

• Clean the magnetic visor with a soft, damp قطعة قماش وصابون خفيف.
• تجنب استخدام المواد الكاشطة التي قد تخدش العدسة.

تخزين

• قم بتخزين الخوذة في مكان بارد وجاف، بعيدًا عن أشعة الشمس المباشرة ودرجات الحرارة القصوى.
• Avoid storing the helmet near chemicals or fumes that could degrade its materials.

استكشاف الأخطاء وإصلاحها

تحديد

Figure 6: This image confirms the Shinmax HT-19 helmet's compliance with European safety standards, as evidenced by its CE certification.

الضمان والدعم

Shinmax products are manufactured to high-quality standards. For warranty information, product support, or to report any issues, please refer to the contact information provided with your purchase or visit the official Shinmax webالموقع. احتفظ بإثبات الشراء الخاص بك لتقديم مطالبات الضمان.