المنتج انتهىview
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
الإعداد والتثبيت
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
قبل أن تبدأ
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- الأدوات المطلوبة: مفك براغي فيليبس، شريط قياس، قلم رصاص.
خطوات التثبيت
- جهز الباب: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- تثبيت المزلاج: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- تأمين التجميع: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- تثبيت لوحة الضربة: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- عملية الاختبار: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
تعليمات التشغيل
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
صيانة
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- تنظيف: Clean the knob and rosette surfaces with a soft, damp قطعة قماش. تجنب استخدام المنظفات الكاشطة أو المذيبات أو مواد التلميع التي قد تتلف السطح.
- تشحيم: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- تشديد مسامير: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- تقتيش: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
استكشاف الأخطاء وإصلاحها
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| المقبض مرتخي أو مهتز. | براغي التثبيت فضفاضة. | Tighten the mounting screws on the interior rosette. |
| لا ينكمش المزلاج بسلاسة. | نقص في التشحيم؛ وجود شوائب في الآلية. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| Door does not close properly or rattles. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
تحديد
- نموذج: Emtek 7103 Passage Set
- مادة: Wrought Steel
- نمط المقبض: Madison Black Knob
- Rosette Style: #3 Rosette
- ينهي: Flat Black Steel (FBS)
- إعداد الباب: Standard 2-1/8" bore hole
- انتكاسة: Standard 2-3/8" (2-3/4" available upon request)
- رمز المنتج العالمي: 751125555226
الضمان والدعم
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek webقد تختلف شروط وأحكام الضمان.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official webالموقع أو داخل عبوة المنتج.
الشركة المصنعة: إمتك
رسمي Webموقع: www.emtek.com
