دليل تعليمات نظام السكة المنزلقة Synology RKS1317

1. المقدمة

1.1 المنتج أكثرview

The Synology RKS1317 Sliding Rail Kit is designed to facilitate the installation and maintenance of compatible Synology RackStation models within a standard server rack. This kit provides a secure and accessible mounting solution, allowing the RackStation to be easily slid in and out of the rack for servicing or cable management.

1.2 الميزات الرئيسية

• آلية الانزلاق: Enables smooth extension and retraction of the RackStation from the rack.
• التوافق: Supports Synology RackStation models with 1U, 2U, and 3U form factors.
• بناء متين: Manufactured from metal for robust and reliable support.
• التثبيت الآمن: Designed for stable attachment to standard server racks.

Figure 1: Synology RKS1317 Sliding Rail Kit. This image displays a single rail from the kit, highlighting its full length and the integrated mounting brackets at both ends.

2. معلومات السلامة

Please read and understand all safety instructions before installing or operating the Synology RKS1317 Sliding Rail Kit. Failure to follow these instructions may result in injury or damage to equipment.

• اعتبارات الوزن: Server equipment can be heavy. Always use proper lifting techniques and seek assistance when handling heavy RackStations to prevent injury.
• بيئة مستقرة: Ensure the server rack is stable and properly secured before installing the rails and RackStation.
• سلامة الأداة: Use appropriate tools for installation and ensure they are in good working condition.
• نقاط الضغط: Be aware of potential pinch points when extending or retracting the rails and RackStation.
• تهوية: Ensure adequate airflow around the RackStation once installed to prevent overheating.

3. محتويات العبوة

تأكد من أن جميع المكونات موجودة وغير تالفة قبل الشروع في التثبيت.

• Synology RKS1317 Sliding Rail (Left)
• Synology RKS1317 Sliding Rail (Right)
• Mounting Screw Kit (typically includes various screws and cage nuts for rack attachment)

4. الإعداد والتثبيت

4.1 قبل أن تبدأ

Before installing the RKS1317 Sliding Rail Kit, ensure your server rack meets the following requirements:

• Rack Mounting Holes: Must be square and at least 3/8 inch x 3/8 inch (approximately 9.5mm x 9.5mm).
• عمق الخزانة: The rack cabinet depth must be between 610mm and 890mm.
• الأدوات المطلوبة: Phillips head screwdriver, measuring tape, and potentially a rack unit (U) marking tool.

4.2 Mounting the Rails to the Rack

1. Identify Rack Units: Determine the desired rack units (U) for your Synology RackStation. Mark the front and rear rack posts accordingly.
2. Attach Front Brackets: Align the front mounting bracket of one sliding rail with the marked square holes on the front rack post. Secure it using the appropriate screws and cage nuts from the mounting kit. Ensure it is level and firmly attached.
3. Extend and Attach Rear Brackets: Extend the sliding rail towards the rear of the rack. Align the rear mounting bracket with the corresponding square holes on the rear rack post. Secure it using screws and cage nuts.
4. Repeat for Second Rail: Install the second sliding rail on the opposite side of the rack, ensuring it is at the same rack unit height and parallel to the first rail.
5. التحقق من الاستقرار: Gently pull and push each installed rail to confirm it is securely mounted and does not wobble.

4.3 Mounting the RackStation to the Rails

1. Prepare RackStation: Ensure any necessary rail mounting brackets are attached to the sides of your Synology RackStation, as per its specific manual.
2. Align RackStation: Carefully align the RackStation with the installed sliding rails. The inner rails of the RKS1317 kit should slide into the corresponding channels on the RackStation's side brackets.
3. Slide In: Gently push the RackStation into the rack. It should slide smoothly along the rails. Do not force the unit. If resistance is met, retract and re-align.
4. Secure RackStation: Once fully inserted, ensure the RackStation is locked into place. Some RackStations may have additional front screws or latches for extra security.

5. التشغيل

5.1 Sliding the RackStation In and Out

The RKS1317 rails allow for easy access to your RackStation for maintenance or cable management.

1. فتح: Locate the release tabs or buttons on the front of the sliding rails (typically on the inner rail section). Press or pull these tabs to disengage the locking mechanism.
2. يمتد: Carefully pull the RackStation forward out of the rack until it reaches its full extension. The rails will lock in the extended position to prevent accidental retraction.
3. تراجع: To push the RackStation back into the rack, press the release tabs again and gently push the unit until it is fully seated and the front locking mechanism engages.

6. الصيانة

6.1 التنظيف

Periodically inspect the rails for dust or debris. Use a dry, lint-free cloth to wipe down the rail surfaces. Avoid using abrasive cleaners or solvents.

6.2 التفتيش

Regularly check all mounting screws and connections to ensure they remain tight. Verify that the sliding mechanism operates smoothly. If any components appear damaged or worn, contact Synology support for assistance.

7. استكشاف الأخطاء وإصلاحها

7.1 Rails Not Sliding Smoothly

• التحقق من المحاذاة: Ensure both rails are installed parallel and at the same height within the rack.
• العوائق: Inspect the rail channels for any debris or foreign objects.
• Over-tightened Screws: Verify that mounting screws are tight but not excessively so, which could deform the rails.

7.2 RackStation Not Fitting or Securing

• التوافق: Confirm your RackStation model is compatible with the RKS1317 rails (1U/2U/3U models).
• RackStation Brackets: Ensure any required RackStation-specific rail brackets are correctly installed on the RackStation itself.
• تنسيق: Re-align the RackStation with the inner rails carefully.

7.3 Rails Not Securely Mounted to Rack

• إحكام المسمار: Re-tighten all mounting screws and cage nuts on both front and rear rack posts.
• Rack Hole Type: Confirm your rack has square mounting holes of the specified size (3/8" x 3/8").
• عمق الخزانة: Ensure your rack's depth is within the specified range (610mm - 890mm).

8. المواصفات

9. الضمان والدعم

For information regarding the warranty coverage for your Synology RKS1317 Sliding Rail Kit, please refer to the warranty card included with your product or visit the official Synology website. For technical support, product registration, or to download the latest documentation, please visit the Synology support portal at www.synology.com/support.