دليل مستخدم مخفف الصوت Bogen AT10A بقوة 10 واط

مقدمة

This manual provides detailed instructions for the installation, operation, and maintenance of the Bogen AT10A 10-Watt Attenuator. The AT10A is designed to control the volume of individual speakers or groups of speakers in a constant voltage (70V or 25V) audio distribution system.

Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or connected equipment.

المنتج انتهىview

الصورة: الجبهة view of the Bogen AT10A 10-Watt Attenuator. The unit features a silver faceplate with a black rotary volume knob. The knob is marked with numbers from 0 to 10, indicating volume levels. The Bogen logo is visible at the bottom center, and "AT-10A" is printed in the bottom right corner.

The Bogen AT10A is a wall-plate style attenuator, providing 10 steps of volume control plus an "OFF" position. It is suitable for use with 25V or 70V constant voltage speaker lines and has a power rating of 10 watts.

الإعداد والتثبيت

احتياطات السلامة

• Ensure all power to the audio system is disconnected before beginning installation.
• يجب أن يتم إجراء التثبيت بواسطة موظفين مؤهلين وفقًا للقوانين الكهربائية المحلية.
• Do not exceed the maximum power rating of 10 watts.

التركيب

1. The AT10A is designed to fit into a standard single-gang electrical box.
2. Secure the electrical box in the desired wall location.
3. Ensure adequate space for wiring connections behind the attenuator.

توصيلات الأسلاك

The AT10A features screw terminals for input and output connections. Refer to the diagram below for typical wiring.

• قم بتوصيل المجلد الثابتtage audio source (e.g., amplifier output) to the "INPUT" terminals.
• Connect the speaker(s) to be controlled to the "OUTPUT" terminals.
• Maintain correct polarity (+ to + and - to -) for all connections.
• تأكد من أن جميع التوصيلات آمنة وخالية من أي دوائر قصر.

(Note: A detailed wiring diagram would typically be provided here by the manufacturer. For this manual, general instructions are given.)

تعليمات التشغيل

The Bogen AT10A provides simple rotary control for adjusting the volume level of connected speakers.

1. تشغيل الطاقة: After installation, restore power to the audio system.
2. ضبط مستوى الصوت: Rotate the knob clockwise to increase the volume and counter-clockwise to decrease it.
3. مستويات الصوت: The knob features marked positions from 0 to 10. Position '0' represents the "OFF" or minimum volume setting, while '10' represents the maximum volume setting.
4. الكون المثالى: Adjust the knob gradually to achieve the desired listening level.

صيانة

The Bogen AT10A is designed for reliable, long-term operation with minimal maintenance.

• تنظيف: To clean the faceplate, gently wipe with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• تقتيش: Periodically check the attenuator for any visible damage or loose connections. If any issues are found, disconnect power and address them promptly.
• لا توجد أجزاء قابلة للصيانة بواسطة المستخدم: The internal components of the AT10A are not user-serviceable. Do not attempt to open or repair the unit. Refer servicing to qualified personnel.

استكشاف الأخطاء وإصلاحها

If troubleshooting steps do not resolve the issue, contact Bogen technical support or a qualified audio technician.

تحديد

معلومات الدعم والاتصال

For technical assistance, product inquiries, or further information, please contact Bogen Communications, Inc.

• الشركة المصنعة: Bogen Communications, Inc.
• Webموقع: www.bogen.com (مثالampالرابط، قد يختلف الرابط الفعلي)
• خدمة العملاء: Refer to the official Bogen webالموقع للحصول على تفاصيل الاتصال الحالية.

ملاحظة: مواصفات المنتج قابلة للتغيير دون إشعار مسبق.