Noyafa NF-909C Fiber Optic Tester User Manual

1. المقدمة

The Noyafa NF-909C is a compact and easy-to-use 2-in-1 testing instrument designed for optical fiber networks. It integrates both an optical power meter and an optical light source, making it suitable for absolute optical power measurements and insertion loss tests. This device offers a wide range of power measurement, high accuracy, and stable output, providing a cost-effective solution for fiber optic testing.

2. معلومات السلامة

• اقرأ الدليل: Before operating the device, thoroughly read and understand this user manual.
• سلامة البطارية: Use only specified 1.5V batteries (3x AAA). Do not mix old and new batteries or different types of batteries. Remove batteries if the device will not be used for an extended period.
• سلامة الليزر: The optical light source emits laser radiation. لا look directly into the optical output port or into a fiber connected to the light source. Direct exposure to laser light can cause severe eye damage.
• الظروف البيئية: Operate the device within the specified operating temperature range (-10°C to +60°C). Avoid exposure to extreme temperatures, humidity, or dust.
• تنظيف: Keep optical connectors clean. Use only approved cleaning methods and materials to avoid damaging the fiber end-faces.
• صيانة: لا تحاول فتح الجهاز أو إصلاحه. أحل جميع أعمال الصيانة إلى فنيين مؤهلين.

3. محتويات العبوة

تأكد من وجود جميع العناصر وأنها في حالة جيدة عند فتح العبوة:

• Noyafa NF-909C Fiber Optic Tester Unit
• دليل المستخدم
• Protective Cap for Optical Ports
• (Batteries may or may not be included depending on the retailer)

4. انتهى المنتجview

The NF-909C features a clear LCD display, intuitive control buttons, and standard optical connectors for versatile use.

الشكل 1: أمام view of the Noyafa NF-909C Fiber Optic Tester. This image shows the device's display screen, the red control buttons (Power, REF, dBm/W, λ, Hz), and the two optical input/output ports on the front, protected by a red cap. The device is black and red.

الشكل 2: جانب view of the Noyafa NF-909C Fiber Optic Tester. This image highlights the micro USB port located on the side of the device, which may be used for power or data transfer, though its primary function is typically for charging or external power supply. The red protective cap is shown detached.

المكونات الرئيسية:

• شاشة LCD: Shows measurement readings, selected wavelength, unit, and battery status.
• أزرار التحكم: Power On/Off, Reference (REF), Unit (dBm/W), Wavelength (λ), Frequency (Hz).
• Optical Power Meter Input: Typically supports SC, ST, LC connectors (optional).
• Optical Light Source Output: Typically FC connector (SC, ST, LC optional).
• حجرة البطارية: Located on the rear, for 3x 1.5V batteries.
• منفذ مايكرو يو اس بي: For power supply or charging (refer to Figure 2).

5. الإعداد

5.1 تركيب البطارية

1. حدد مكان غطاء حجرة البطارية على الجزء الخلفي للجهاز.
2. قم بسحب الغطاء أو فكه لفتحه.
3. أدخل ثلاث (3) بطاريات AAA بجهد 1.5 فولت، مع التأكد من صحة القطبية (+/-) كما هو موضح داخل الحجرة.
4. أعد تركيب غطاء حجرة البطارية بشكل آمن.

5.2 التشغيل المبدئي

اضغط مع الاستمرار على قوة button to turn on the device. The LCD display will illuminate, showing the current mode and settings.

6. تعليمات التشغيل

6.1 Optical Power Meter Mode

This mode measures the absolute optical power or relative loss in optical fiber networks.

1. توصيل الألياف: Connect the optical fiber to be tested to the Power Meter input port. Ensure the connector is clean.
2. حدد الطول الموجي: اضغط على λ button to cycle through the available calibrated wavelengths: 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. Select the wavelength matching your light source.
3. View قياس: The display will show the optical power in dBm.
4. Change Unit: اضغط على ديسيبل / واط button to switch between dBm and W (Watts) units.
5. Set Reference (REF): For relative measurements (loss), connect a known good fiber to a stable light source and the power meter. Press the مرجع button to set the current power reading as the reference (0dB). Subsequent measurements will show the loss relative to this reference.
6. Frequency Identification: The power meter can identify modulation frequencies from 10Hz to 60KHz. If the incoming signal is modulated, the frequency will be displayed.

6.2 Optical Light Source Mode

This mode provides a stable optical signal for testing fiber optic cables.

1. توصيل الألياف: Connect the optical fiber to be tested to the Light Source output port. Ensure the connector is clean.
2. حدد الطول الموجي: اضغط على λ button to cycle through the available wavelengths: 1310nm and 1550nm. Select the desired wavelength.
3. Select Modulation Frequency: اضغط على Hz button to cycle through modulation frequencies: 270Hz, 1KHz, 2KHz, or continuous wave (CW).
4. إشارة الخرج: The device will emit a stable optical signal at the selected wavelength and modulation.

6.3 وظيفة الإيقاف التلقائي

The device features an auto-off function to conserve battery life. If no operation is performed for approximately 15 minutes, the device will automatically power off. Press the قوة اضغط على الزر لإعادة تشغيله.

7. الصيانة

• تنظيف الموصلات الضوئية: Always ensure optical connectors are clean before use. Use lint-free wipes and appropriate optical cleaning solutions. Dirty connectors can lead to inaccurate measurements and damage to the device or fiber.
• استبدال البطارية: When the battery indicator on the display shows low power, replace all three 1.5V AAA batteries promptly.
• تخزين: When not in use, store the device in a dry, cool place, away from direct sunlight and extreme temperatures. Always replace the protective caps on the optical ports to prevent dust and damage.
• التنظيف الخارجي: نظف السطح الخارجي للجهاز بقطعة ناعمة ، دamp القماش. لا تستخدم المنظفات أو المذيبات الكاشطة.

8. استكشاف الأخطاء وإصلاحها

• الجهاز لا يعمل:
  • تأكد من تركيب البطاريات بشكل صحيح مع مراعاة القطبية المناسبة.
  • استبدلها ببطاريات جديدة.
• Inaccurate power meter readings:
  • Ensure optical connectors are clean.
  • Verify the selected wavelength on the power meter matches the light source wavelength.
  • Check if the fiber under test is properly connected and not damaged.
• No light output from light source:
  • Ensure the device is powered on and in light source mode.
  • تحقق من مستوى البطارية.
  • Verify the fiber is properly connected to the output port.
• Auto-off activates too quickly:
  • The auto-off is fixed at 15 minutes of inactivity. This is normal operation.

9. المواصفات

10. الضمان والدعم

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or contact your authorized Noyafa dealer or the manufacturer directly. Keep your purchase receipt as proof of purchase.