Hella BMW Angel Eye Parking Light Bulb with Socket Instruction Manual

1. المقدمة

This instruction manual provides essential information for the proper installation, operation, and maintenance of your Hella BMW Angel Eye Parking Light Bulb with Socket (Model: 9DX 153 746-011). Please read this manual thoroughly before installation and retain it for future reference. This product is designed as a replacement part for specific BMW vehicle models requiring an H10W bulb type for front parking lights (Angel Eyes).

2. معلومات السلامة

• افصل بطارية السيارة دائمًا قبل القيام بأي عمل كهربائي لمنع حدوث صدمة كهربائية أو تلف النظام الكهربائي للسيارة.
• ارتدِ معدات الحماية الشخصية المناسبة، مثل القفازات وحماية العين، أثناء التثبيت.
• تأكد من ركن السيارة على سطح مستوٍ مع تشغيل فرامل الانتظار.
• Allow the existing bulb to cool down completely before handling, as it can be very hot.
• إذا لم تكن متأكدًا من أي خطوة من خطوات عملية التثبيت، فاستشر فني سيارات مؤهلًا.
• Dispose of old bulbs and packaging materials responsibly according to local regulations.

3. محتويات العبوة

تأكد من أن جميع المكونات موجودة وغير تالفة قبل الشروع في التثبيت.

• 1 x Hella BMW Angel Eye Parking Light Bulb with Socket

الصورة 3.1: The Hella Angel Eye Parking Light Bulb with Socket, shown with its yellow product packaging. The bulb and socket assembly are visible, featuring a clear H10W bulb, a black plastic socket, and a red sealing ring. The packaging displays the Hella logo and product information.

4. الإعداد والتثبيت

This section outlines the general procedure for replacing the Angel Eye parking light bulb and socket. Specific steps may vary slightly depending on your BMW model. Refer to your vehicle's service manual for detailed instructions.

1. إعداد السيارة: Park the vehicle on a flat, stable surface. Engage the parking brake and turn off the engine. Allow the headlight assembly to cool down.
2. الوصول إلى مجموعة المصابيح الأمامية: Depending on your BMW model, you may need to open the hood and locate the rear access panel for the headlight assembly. Some models might require partial removal of the wheel well liner or other components to gain access.
3. Locate the Angel Eye Bulb Socket: Identify the specific socket for the Angel Eye parking light. It is typically located at the back of the headlight housing.
4. Disconnect the Electrical Connector: Carefully disconnect the electrical connector from the old bulb socket. This usually involves pressing a tab and pulling the connector away.
5. Remove the Old Bulb Socket: Twist the old bulb socket counter-clockwise (or as indicated by your vehicle's manual) to unlock it from the headlight housing. Gently pull the socket and bulb assembly out.
6. Inspect the New Bulb Socket: Before installation, visually inspect the new Hella bulb and socket for any damage.
7. Insert the New Bulb Socket: Align the new Hella bulb socket with the opening in the headlight housing. Push it in gently and twist clockwise until it locks securely into place. Ensure the red sealing ring is properly seated to prevent moisture ingress.
8. Connect the Electrical Connector: Reconnect the vehicle's electrical connector to the new bulb socket. Ensure it clicks firmly into place.
9. اختبار الضوء: Turn on the vehicle's parking lights to verify that the new Angel Eye bulb illuminates correctly.
10. إعادة التجميع: Reinstall any components that were removed to gain access to the headlight assembly.

الصورة 4.1: لقطة مقرّبة view of the Hella Angel Eye Parking Light Bulb with Socket. The H10W bulb is clearly visible within its reflective housing, surrounded by the black plastic socket and the red sealing gasket. This image highlights the design of the bulb and its integrated socket for direct replacement.

5. تعليمات التشغيل

The Hella Angel Eye Parking Light Bulb with Socket operates as part of your vehicle's existing lighting system. Once correctly installed, it will illuminate when the vehicle's parking lights or headlights are activated, depending on your vehicle's specific wiring and control settings.

• To activate: Turn your vehicle's light switch to the parking light or headlight position.
• To deactivate: Turn your vehicle's light switch to the off position.

No additional user interaction is required for the operation of this component beyond the standard vehicle lighting controls.

6. الصيانة

The Hella Angel Eye Parking Light Bulb with Socket is designed for long-lasting performance with minimal maintenance. However, periodic inspection can help ensure optimal function.

• التفتيش البصري: Periodically check the Angel Eye lights for proper illumination. If one side appears dimmer or is not lighting up, it may indicate a failing bulb or electrical issue.
• تنظيف: If the headlight lens becomes dirty, clean it with a soft cloth and appropriate automotive cleaning solution. Avoid abrasive cleaners that could scratch the lens.
• الاستبدال: The bulb is integrated into the socket. If the bulb fails, the entire bulb and socket assembly must be replaced. Refer to Section 4 for replacement instructions.

7. استكشاف الأخطاء وإصلاحها

If you encounter issues with your Hella Angel Eye Parking Light Bulb with Socket, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, it is recommended to consult a professional automotive technician.

8. المواصفات

9. الضمان والدعم

For information regarding product warranty, please refer to the warranty documentation provided with your purchase or visit the official Hella website. For technical support or further assistance, please contact Hella customer service through their official channels.

Hella Official Webموقع: www.hella.com