1. المقدمة
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Legrand E14 Lamp Holder, model LEG91123. This product is designed for use with E14 screw-base bulbs, with a maximum wattage of 60W and operating at 230 Volts.
2. معلومات السلامة
WARNING: Risk of electric shock. Always disconnect power at the main circuit breaker before installing or servicing electrical components.
- يجب أن يتم التركيب فقط بواسطة كهربائي مؤهل أو شخص مختص.
- Ensure the power supply is completely off before beginning any work.
- لا تتجاوز الحد الأقصى للواط المقننtage of 60W for the connected bulb.
- تأكد من أن جميع التوصيلات آمنة ومعزولة بشكل صحيح.
- This product is designed for indoor use in dry locations only.
3. مكونات المنتج
The Legrand E14 Lamp Holder consists of several parts designed for secure and reliable bulb connection.
Figure 3.1: Complete Legrand E14 Lamp Holder. This image shows the complete Legrand E14 lamp holder, featuring the threaded body for bulb insertion and the base for electrical connection.
Figure 3.2: Legrand E14 Lamp Holder disassembled. This image illustrates the main components of the Legrand E14 lamp holder, including the outer casing, internal mechanism, and shade ring.
- ج الخارجيasing: Made of white polyamide material, providing insulation and protection.
- الآلية الداخلية: Contains the electrical contacts and wiring terminals.
- Shade Ring: Used to secure a lampظل إلى لamp حامل.
4. تعليمات التثبيت
Follow these steps for proper installation of the Legrand E14 Lamp مالك.
- تحضير الأسلاك: Ensure the power supply is disconnected. Strip approximately 8-10mm of insulation from the ends of the electrical wires.
- محطات الوصول: لamp holder's internal mechanism may need to be partially disassembled to access the wiring terminals. Refer to Figure 3.2 for component identification.
- توصيل الأسلاك: Insert the stripped wire ends into the designated terminals. The wire entry can be from the side or via a screw connection. Secure the wires firmly by tightening the terminal screws. Ensure no loose strands are present.
Figure 4.1: Internal wiring terminals. This image displays the internal wiring terminals of the Legrand E14 lamp holder, where electrical wires are connected.
- إعادة التجميع: Carefully reassemble the lamp holder components, ensuring all parts are correctly aligned and secured.
- التركيب: لamp holder is designed for installation on a Ø10 male connector. Secure the lamp holder to the fixture using the appropriate mounting method.
- Attach Shade Ring (Optional): إذا كنت تستخدم آلampshade, slide the shade ring over the threaded part of the lamp holder and tighten it to secure the lampظل.
5. التشغيل
Once installed, operating the lamp holder is straightforward:
- إدراج لمبة: Gently screw an E14 screw-base bulb into the lamp حتى يصبح الحامل محكمًا. لا تشدّه كثيرًا.
- اعادة الطاقة: Turn on the power supply at the main circuit breaker.
- امتحان: Activate the light switch to confirm proper operation.
6. الصيانة
The Legrand E14 Lamp Holder requires minimal maintenance.
- تنظيف: Disconnect power before cleaning. Wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- تقتيش: فحص دوري لamp holder for any signs of damage, wear, or loose connections. If any issues are found, disconnect power and address them immediately.
- استبدال المصباح: Always disconnect power before replacing a bulb. Allow the old bulb to cool completely before removal.
7. استكشاف الأخطاء وإصلاحها
إذا واجهت مشاكل مع جهازكamp holder, refer to the following common problems and solutions:
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| الضوء لا يضيء | لا يوجد مصدر للطاقة | تحقق من قاطع الدائرة ومفتاح الحائط. |
| الضوء لا يضيء | لمبة معيبة | Replace the bulb with a new, working E14 bulb (max 60W). |
| الضوء لا يضيء | اتصال الأسلاك فضفاض | Disconnect power and check all wire connections within the lamp holder. Tighten if necessary. |
| ضوء متقطع | لمبة فضفاضة أو اتصال | Ensure the bulb is screwed in tightly. Disconnect power and check wiring connections. |
8. المواصفات الفنية
- ماركة: ليجراند
- رقم الموديل: ساقه 91123
- نوع المصباح: E14 Screw-base
- مادة: Polyamide-Imide
- لون: أبيض
- المجلدtage: 230 فولت
- الحد الأقصى للطاقة: 60 واط
- أبعاد المنتج (الطول × العرض × الارتفاع): 3 × 3 × 6 سم
- وزن: 50 جرام
- نوع التركيب: For Ø10 male connector
- المواصفات المتوافقة: NF
- بلد المنشأ: الصين
9. الضمان والدعم
For warranty information or technical support, please refer to the documentation provided with your purchase or contact Legrand customer service directly. Keep your proof of purchase for warranty claims.