دليل تعليمات مستشعر اللهب لمجفف ويرلبول 338906

1. انتهى المنتجview

This manual provides instructions for the Whirlpool 338906 Dryer Flame Sensor. This component is a genuine replacement part designed to ensure the proper and safe operation of compatible Whirlpool gas dryers. The flame sensor monitors the presence of a flame in the dryer's burner assembly, signaling the control system to continue the heating cycle. If no flame is detected, the sensor will cause the gas valve to shut off, preventing unburned gas from accumulating.

Figure 1: Whirlpool 338906 Dryer Flame Sensor in its original packaging, indicating it is a genuine Whirlpool quality part.

ال 338906 sensor is crucial for the safety and efficiency of your dryer's heating system. It is compatible with various Whirlpool dryer models, including 1276^0A, 1276W0A, 1CWD5100VQ0, 1CWGD5100VQ1, 1CWGD5200VQ0, 1CWGD5200VQ1, 1CWGD5300VW0, 1CWGD5790VQ0, and 1CWGD5790VQ1.

2. معلومات هامة حول السلامة

WARNING: Before attempting any repair or installation, always disconnect the dryer from its power source (unplug it or turn off the circuit breaker) and shut off the gas supply. Failure to do so can result in electric shock, gas leak, fire, or serious injury.

• Always wear appropriate personal protective equipment, such as gloves, during installation.
• تأكد من أن منطقة العمل جيدة التهوية.
• إذا لم تكن متأكدًا من أي خطوة، فاستشر فني أجهزة مؤهلًا.
• Use only genuine Whirlpool replacement parts to ensure compatibility and safety.
• After installation, check for any gas leaks if working with gas lines.

3. تعليمات التثبيت

Replacing the flame sensor requires accessing the dryer's internal components. The general steps are outlined below. Specific disassembly procedures may vary by dryer model. Refer to your dryer's service manual for detailed instructions.

الأدوات المطلوبة:

• فيليبس رئيس مفك
• 1/4 بوصة سائق الجوز
• Flat-bladed screwdriver or putty knife (for opening dryer panels)

خطوات التثبيت العامة:

1. افصل الكهرباء والغاز: Unplug the dryer from the electrical outlet and turn off the gas supply valve.
2. Access Dryer Interior: Depending on your model, this may involve removing the top panel, front panel, or rear panel. Typically, the front panel needs to be removed to access the burner assembly.
3. Locate the Flame Sensor: The flame sensor is usually located near the igniter and burner tube within the burner assembly. It is a small component with two wires connected to it.


الشكل 2: لقطة مقربة view of the Whirlpool 338906 Flame Sensor, showing its electrical terminals and mounting bracket.

4. فصل الأسلاك: Carefully disconnect the two electrical wires from the old flame sensor. Note their orientation if necessary, though they are typically non-polarized.
5. إزالة المستشعر القديم: Unscrew the mounting screw(s) that secure the flame sensor to its bracket or the burner assembly. Remove the old sensor.

Figure 3: Another perspective of the Whirlpool 338906 Flame Sensor, highlighting the "THERM-O-DISC" branding and patent numbers.
6. تثبيت المستشعر الجديد: Position the new Whirlpool 338906 flame sensor in the same location as the old one. Secure it with the mounting screw(s).


الشكل 4: القاع view of the Whirlpool 338906 Flame Sensor, showing the sensor element and its housing.

7. إعادة توصيل الأسلاك: Reconnect the electrical wires to the new sensor.
8. إعادة تجميع المجفف: Reattach any panels or components that were removed. Ensure all screws are tightened and panels are securely in place.
9. استعادة الكهرباء والغاز: Turn on the gas supply and plug the dryer back into the electrical outlet.
10. عملية الاختبار: Run a short drying cycle to confirm proper heating and operation. Listen for the igniter and burner to cycle correctly.

IMPORTANT: If you detect any gas odor after restoring the gas supply, immediately shut off the gas, open windows for ventilation, and contact a qualified technician or your gas provider. Do not operate the dryer.

4. Operation of the Flame Sensor

The Whirlpool 338906 flame sensor operates as a safety and control device within your gas dryer. When the dryer starts a heating cycle, the igniter glows to ignite the gas. Once a flame is established, the flame sensor detects its presence. This detection signals the dryer's control board that the burner is operating correctly, allowing the gas valve to remain open and the heating cycle to continue.

If the flame sensor does not detect a flame (e.g., due to a faulty igniter, gas supply issue, or a defective sensor itself), it will signal the control board to shut off the gas valve, preventing unburned gas from entering the dryer drum or exhaust system. This mechanism is critical for preventing fire hazards and ensuring efficient drying.

5. الصيانة

The Whirlpool 338906 flame sensor is a sealed component and does not require routine maintenance or cleaning. However, ensuring the overall cleanliness of your dryer can contribute to the longevity of all its components, including the flame sensor.

• تنظيف فلتر الوبر: Always clean the lint filter before or after every load to maintain proper airflow and prevent lint buildup, which can affect dryer performance and safety.
• Inspect Exhaust Vent: Periodically inspect and clean the dryer's exhaust vent system to ensure it is free of lint and obstructions. A clogged vent can cause the dryer to overheat and potentially damage components.
• التفتيش المهني: Consider having your dryer professionally inspected every few years to ensure all components, including safety sensors, are functioning correctly.

6. استكشاف المشكلات الشائعة وإصلاحها

If your dryer is experiencing heating problems after replacing the flame sensor, or if you suspect the sensor is faulty, consider the following:

إذا لم تنجح خطوات استكشاف الأخطاء وإصلاحها في حل المشكلة، يُنصح باستشارة فني إصلاح أجهزة مؤهل.

7. مواصفات المنتج

8. الضمان والدعم

As a genuine Whirlpool replacement part, the 338906 flame sensor is typically covered by Whirlpool's standard warranty for replacement parts. Please refer to the warranty documentation included with your purchase or visit the official Whirlpool webالموقع لمعرفة شروط وأحكام الضمان المحددة.

For technical support, service inquiries, or to locate authorized service providers, please visit the official Whirlpool support website or contact their customer service department. Using genuine parts ensures compatibility and maintains the integrity of your appliance's warranty.

Figure 5: Whirlpool Corporation Factory Certified Parts & Accessories banner, emphasizing the importance of genuine parts.