دليل مستخدم مقياس سمك الطلاء VOLTCRAFT SDM-115

1. المقدمة

The VOLTCRAFT SDM-115 Coating Thickness Gauge is designed to quickly and accurately measure the coating thickness on metallic surfaces. This device helps determine if a painted or repaired surface requires repainting or further repair. It is suitable for use on both ferromagnetic (e.g., steel) and non-ferromagnetic (e.g., aluminum) metals, offering a measurement range of 0-1000 µm.

2. معلومات السلامة

يرجى قراءة وفهم جميع تعليمات السلامة قبل تشغيل الجهاز. قد يؤدي عدم اتباع هذه التعليمات إلى إصابة أو تلف الجهاز.

• احفظ الجهاز بعيدًا عن الماء والرطوبة.
• لا تحاول فتح الجهاز أو تعديله. أحل جميع أعمال الصيانة إلى فنيين مؤهلين.
• Use only the specified battery type. Ensure correct polarity when installing batteries.
• تجنب تعريض الجهاز لدرجات حرارة شديدة أو لأشعة الشمس المباشرة.
• يحفظ بعيدًا عن متناول الأطفال.

3. انتهى المنتجview

The VOLTCRAFT SDM-115 is a handheld coating thickness gauge featuring an ergonomic design for comfortable use. It includes a digital display and intuitive control buttons for calibration, unit selection, and backlight control.

الشكل 3.1: أمام view of the VOLTCRAFT SDM-115 Coating Thickness Gauge, showing the display and control buttons.

المميزات الرئيسية:

• Measures coating thickness on ferromagnetic and non-ferromagnetic metals.
• Measurement range: 0-1000 µm.
• Two-point calibration for enhanced accuracy.
• Digital display with backlight.
• Unit selection between mils and micrometers (µm).

الشكل 3.2: جانب view of the VOLTCRAFT SDM-115, highlighting its ergonomic design and trigger.

4. الإعداد

4.1 تركيب البطارية

The VOLTCRAFT SDM-115 requires batteries for operation (not included). To install batteries:

1. Locate the battery compartment cover, typically on the handle of the device.
2. قم بسحب الغطاء أو فكه لفتح الحجرة.
3. أدخل البطاريات المطلوبة، مع التأكد من صحة القطبية (+/-) كما هو موضح داخل الحجرة.
4. أغلق غطاء حجرة البطارية جيدًا.

5. تعليمات التشغيل

5.1 تشغيل/إيقاف التشغيل

Press and hold the trigger or power button (if available) to turn the device on. The display will illuminate. To turn off, press and hold the same button or wait for automatic shutdown.

5.2 أخذ القياس

To take an accurate coating thickness measurement:

1. Ensure the measurement surface is clean, dry, and free of debris.
2. Place the sensor head of the gauge firmly and perpendicularly onto the surface to be measured.
3. The device will automatically display the coating thickness reading on the screen.
4. ارفع الجهاز من على السطح استعدادًا للقياس التالي.

الشكل 5.1: The VOLTCRAFT SDM-115 being used to measure a surface.

5.3 تغيير وحدات القياس

The device supports measurement in both mils and micrometers (µm). To switch between units, press the button labeled mils/µm على لوحة التحكم.

6. المعايرة

For optimal accuracy, especially when measuring different materials or after prolonged use, two-point calibration is recommended. The device features a كال button for initiating the calibration process.

While the exact steps for two-point calibration may vary, generally it involves:

1. Placing the gauge on a known zero-thickness surface (e.g., bare metal).
2. الضغط على كال button and following on-screen prompts to set the zero point.
3. Placing the gauge on a surface with a known standard thickness (e.g., a calibration foil).
4. الضغط على كال button again and using the arrow buttons to adjust the reading to match the known standard thickness.
5. Confirming the calibration.

Refer to the detailed instructions provided with your specific calibration foils or the full product manual for precise calibration procedures.

7. الصيانة

7.1 التنظيف

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the sensor head is kept clean and free of dust or residue for accurate readings.

7.2 التخزين

Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for an extended period, remove the batteries to prevent leakage.

8. استكشاف الأخطاء وإصلاحها

• الجهاز لا يعمل: تحقق من تركيب البطارية وتأكد من عدم نفادها. استبدلها إذا لزم الأمر.
• قراءات غير دقيقة أو غير متسقة:
  • Ensure the sensor head is clean and free of debris.
  • Perform a two-point calibration as described in Section 6.
  • Verify the measurement surface is clean, dry, and flat.
  • Ensure the device is placed perpendicularly and firmly on the surface.
• Device beeps excessively or shows unusually high values: This often indicates a need for calibration. Follow the calibration steps in Section 6 carefully. Ensure you are using appropriate calibration standards.

9. المواصفات

10. الضمان والدعم

For warranty information, technical support, or service inquiries, please refer to the documentation included with your purchase or contact VOLTCRAFT customer service directly. Please have your model number (SDM-115) and article number (100847) available when contacting support.