Lithonia Lighting Fluorescent Troffer Instruction Manual

مقدمة

This manual provides essential instructions for the safe installation, operation, and maintenance of your Lithonia Lighting 2GT8 2 U316 A12 MVOLT GEB10IS Fluorescent Troffer. Please read all instructions carefully before proceeding with installation or use. Retain this manual for future reference.

معلومات السلامة

• افصل دائمًا الطاقة عن قاطع الدائرة قبل تثبيت أو صيانة أو تنظيف التركيبات.
• Installation should be performed by a qualified electrician in accordance with all applicable national and local electrical codes.
• تأكد من تأريض الجهاز بشكل صحيح لتجنب الصدمة الكهربائية المحتملة.
• لا تقم بتثبيته بالقرب من المواد القابلة للاشتعال.
• ارتدِ معدات الحماية الشخصية المناسبة أثناء التركيب والصيانة.

يثبت

تثبيت

The Lithonia Lighting 2GT8 troffer is designed for recessed installation in grid ceilings. Follow these general steps:

1. تحضير فتحة السقف: Ensure the ceiling grid opening matches the fixture dimensions (24 x 24 inches).
2. التوصيلات الكهربائية: Route electrical supply wires to the fixture location. Connect the fixture's wiring to the building's electrical system according to local codes. Ensure proper grounding.
3. التركيب: Carefully lift the troffer into the ceiling grid opening. The fixture is designed for lay-in grid installation. Secure the fixture to the grid using appropriate clips or hangers as required by local codes.
4. تركيب المصابيح: Install two (2) U31W T8 fluorescent bulbs (not included) into the fixture's sockets. Ensure bulbs are seated correctly.
5. تركيب العدسة: Close and secure the hinged steel door with the acrylic patterned lens.

Refer to the mounting data and dimensions diagram below for detailed measurements and installation guidance.

Image: A technical diagram illustrating the mounting data and dimensions of the Lithonia Lighting 2GT8 troffer. It shows various measurements in inches and millimeters for the fixture's depth, width, and mounting points, along with a small diagram of a lay-in grid installation.

التشغيل

التشغيل الأساسي

Once installed and wired correctly, the Lithonia Lighting 2GT8 troffer operates by a standard wall switch connected to the electrical circuit. Ensure the correct T8 fluorescent bulbs are installed before restoring power.

استبدال المصباح

لاستبدال المصابيح:

1. فصل الطاقة: قم بفصل التيار الكهربائي عن الجهاز من قاطع الدائرة.
2. Open Lens: Unlatch and open the hinged steel door to access the bulbs.
3. إزالة المصابيح القديمة: Carefully twist and remove the old T8 fluorescent bulbs.
4. Install New Bulbs: Insert new U31W T8 fluorescent bulbs, ensuring they are securely seated in the sockets.
5. Close Lens: Close and secure the hinged steel door.
6. اعادة الطاقة: أعد تشغيل الطاقة عند قاطع الدائرة.

صيانة

تنظيف

Regular cleaning helps maintain optimal light output and appearance.

• فصل الطاقة: احرص دائمًا على فصل التيار الكهربائي قبل التنظيف.
• المظهر الخارجي النظيف: امسحي الأسطح الخارجية بقطعة ناعمة ، دamp قماش. تجنب المنظفات الكاشطة.
• عدسة نظيفة: The acrylic patterned lens can be cleaned with a mild, non-abrasive cleaner specifically designed for plastics. Open the hinged door for easier access.
• تأكد من جفاف جميع الأجزاء قبل إعادة تشغيل الطاقة.

استبدال العدسة

The hinged steel door allows for easy replacement of the acrylic patterned lens if it becomes damaged or discolored. Contact Lithonia Lighting customer support for replacement lens options.

استكشاف الأخطاء وإصلاحها

If you encounter issues with your fluorescent troffer, refer to the following common problems and solutions:

• الضوء لا يضيء:
  • تحقق من تعطل قاطع الدائرة.
  • Verify that bulbs are correctly installed and not faulty.
  • تأكد من أن جميع توصيلات الأسلاك آمنة.
• وميض الضوء:
  • Replace old or faulty fluorescent bulbs.
  • Check for loose bulb connections.
  • A failing ballast may cause flickering; consult a qualified electrician for inspection.
• انخفاض في شدة الإضاءة:
  • Clean the lens and bulbs to remove dust and debris.
  • Bulbs may be nearing the end of their lifespan and require replacement.

For persistent issues, contact customer support or a qualified electrician.

تحديد

Key specifications for the Lithonia Lighting 2GT8 2 U316 A12 MVOLT GEB10IS Fluorescent Troffer:

For additional technical details, refer to the product datasheet below.

Image: A section of the Lithonia Lighting 2GT8 product datasheet, detailing features, specifications, and ordering information for various configurations of the 2GT8 series troffer, including the 2GT8 2 U316 A12 MVOLT GEB10IS model.

معلومات الضمان

This Lithonia Lighting product is covered by a ضمان محدود لمدة سنة واحدة. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, please refer to the official warranty documentation provided with your purchase or visit the Lithonia Lighting webموقع.

دعم العملاء

For technical assistance, replacement parts, or warranty claims, please contact Lithonia Lighting customer support.

• الشركة المصنعة: Acuity Brands Lighting Inc.
• الدعم عبر الإنترنت: قم بزيارة الموقع الرسمي متجر ليثونيا للإضاءة لمزيد من المعلومات والموارد.