ANEX Ultra Low Profile دليل استخدام مفك براغي ذو تروس منحرف، موديل 436

1. المقدمة

This manual provides instructions for the safe and effective use of your ANEX Ultra Low Profile Offset Ratcheting Screwdriver, Model 436. This tool is designed for accessing and fastening screws in confined or hard-to-reach areas where traditional screwdrivers cannot be used.

2. معلومات السلامة

• Always wear appropriate eye protection when using hand tools.
• Ensure the screwdriver bit is correctly seated and matches the screw head type and size to prevent stripping the screw or damaging the bit.
• Do not use the tool for purposes other than its intended use as a screwdriver.
• احرص على إبقاء يديك وأصابعك بعيدًا عن الأجزاء المتحركة، وخاصة آلية السقاطة.
• Store the tool in a dry, safe place away from children.

3. انتهى المنتجview

The ANEX Model 436 features a low-profile, offset design with a ratcheting mechanism, ideal for tight spaces. It includes a magnetic bit holder for secure bit retention.

الشكل 3.1: بشكل عام view of the ANEX Ultra Low Profile Offset Ratcheting Screwdriver with an inserted bit.

الشكل 3.2: الصورة عن قرب view of the magnetic bit holder, ensuring bits are securely held during use.

4. الإعداد

The ANEX Model 436 comes with two standard bits: a Phillips (+2 mm) and a Flathead (-6 mm).

1. حدد القطعة الصحيحة: Choose the appropriate bit (Phillips or Flathead) that matches the screw head you intend to work with.
2. أدخل البت: Firmly push the selected bit into the magnetic bit holder at the end of the ratcheting head. The magnet will secure the bit in place.

5. التشغيل

5.1 Ratcheting Mechanism

The screwdriver features a three-position switch on the ratcheting head:

• للأمام (شد): Position the switch to allow rotation in the clockwise direction for tightening screws.
• عكس (فك): Position the switch to allow rotation in the counter-clockwise direction for loosening screws.
• مغلق: Position the switch to lock the head, allowing the tool to be used as a fixed screwdriver.

5.2 Using in Tight Spaces

The ultra-low profile and 90-degree offset head are specifically designed for areas with limited clearance. Insert the bit into the screw head, ensuring a snug fit. The flat handle allows for easy application of pressure.

Figure 5.1: Demonstrating the screwdriver's ability to access screws in extremely tight and confined areas.

5.3 Applying Pressure

For effective fastening or loosening, apply downward pressure on the flat handle while rotating the tool. The design of the handle facilitates this, even in awkward positions.

Figure 5.2: Illustration of proper hand placement and pressure application for optimal use.

6. الصيانة

• تنظيف: Wipe the tool clean with a dry cloth after each use to remove dirt, grease, or debris. Do not use harsh chemicals or abrasive cleaners.
• تخزين: Store the screwdriver and bits in a clean, dry environment to prevent rust and damage.
• تقتيش: Periodically inspect the tool for any signs of wear or damage. Discontinue use if any damage is found and replace if necessary.

7. استكشاف الأخطاء وإصلاحها

• Bit Slipping: Ensure the bit is fully inserted into the magnetic holder and that it correctly matches the screw head. Worn bits should be replaced.
• آلية الرفع غير منخرطة: Check the direction switch to ensure it is fully engaged in either the forward or reverse position, not in between.
• Difficulty Turning Screws: Ensure sufficient downward pressure is applied. For extremely tight screws, apply penetrating oil if appropriate for the application.

8. المواصفات

Figure 8.1: Detailed dimensions of the screwdriver, including length and thickness.

9. الضمان والدعم

Specific warranty information for the ANEX Ultra Low Profile Offset Ratcheting Screwdriver Model 436 is not provided in this document. For warranty details, product support, or service inquiries, please contact the manufacturer directly or refer to the product packaging.