دليل تعليمات هوائي Comet CHA-250HD ذو القاعدة العمودية متعدد النطاقات

1. المقدمة

The Comet CHA-250HD All Band Vertical Base Antenna is designed for continuous operation across a wide frequency range of 3.5 to 57 MHz. This antenna covers popular amateur radio bands including 80m, 40m, 20m, 15m, 10m, and 6m, without requiring external tuners or radials. Its construction features a durable fiberglass radiating element and corrosion-resistant aluminum hardware, ensuring resilience against various weather conditions. An integrated transformer matching network optimizes impedance across multiple bands, contributing to efficient signal transfer and minimal SWR.

المميزات الرئيسية:

• Continuous 3.5–57 MHz coverage without manual tuning or external antenna tuners.
• Built-in transformer matching network for consistent impedance and low SWR.
• Constructed from high-quality fiberglass with a reinforced weatherproof coating.
• Efficient wideband design eliminates the need for ground radials or multiple antennas.
• Rated at 250 watts PEP and features an SO-239 connector.

2. محتويات العبوة

Before beginning assembly, ensure all components are present and undamaged. The package should contain the following:

• CHA-250HD Antenna Main Unit (Fiberglass radiating elements)
• Transformer Matching Network (Base unit with SO-239 connector)
• Mounting Hardware (U-bolts, nuts, washers for mast mounting)
• دليل التعليمات

Figure 1: All components of the CHA-250HD antenna kit.

3. الإعداد والتثبيت

The CHA-250HD is designed for straightforward installation. No complex tuning or ground radials are typically required for operation. However, proper mounting is essential for optimal performance and longevity.

3.1 اختيار الموقع

• Choose a location free from obstructions (trees, buildings, power lines) that could interfere with signal propagation.
• Mount the antenna as high as safely possible to maximize range and minimize local interference.
• Ensure the mounting surface (mast, tower, roof) is sturdy enough to support the antenna's weight and withstand wind loads.

3.2 خطوات التجميع

1. Attach Radiating Elements: Carefully connect the fiberglass radiating elements to the transformer matching network base unit. Ensure all connections are secure but do not overtighten.
2. شريحة متزايدة: Secure the mounting bracket to the antenna base using the provided hardware.
3. تركيب الصاري: Using the U-bolts, attach the antenna to your chosen mast or pole. Ensure the antenna is mounted vertically and securely.
4. اتصال الكابل المحوري: Connect a high-quality 50-ohm coaxial cable (e.g., RG-8X, RG-213) to the SO-239 connector at the base of the antenna. Ensure the connection is weatherproofed using self-amalgamating tape or similar.

Figure 2: Close-up of the antenna base and mounting bracket.

Figure 3: Fully assembled Comet CHA-250HD antenna.

4. تعليمات التشغيل

The CHA-250HD is designed for wideband operation, eliminating the need for an external antenna tuner for most amateur radio transceivers. However, always monitor your SWR (Standing Wave Ratio) to ensure safe and efficient operation.

4.1 SWR Monitoring

• Before transmitting, perform an SWR check across your desired operating frequencies.
• An SWR of 1.5:1 or lower is generally considered excellent. Up to 2.0:1 is acceptable for most transceivers.
• If SWR is excessively high (e.g., above 3.0:1), recheck all connections and ensure the antenna is clear of obstructions.
• Confirm the antenna is mounted vertically and not hanging more than 20 degrees from vertical.

4.2 التعامل مع الطاقة

• The CHA-250HD is rated for 250 watts PEP (Peak Envelope Power).
• Avoid exceeding the maximum power rating to prevent damage to the antenna or your transceiver.
• For digital modes, it is recommended to operate at lower power levels (e.g., below 80W) due to the continuous duty cycle.

5. الصيانة

The Comet CHA-250HD is designed for minimal maintenance due to its durable construction. However, periodic checks can extend its lifespan and ensure continued performance.

• التفتيش البصري: Annually inspect the antenna for any visible damage, cracks in the fiberglass, or loose hardware.
• فحص الاتصال: Verify that all coaxial cable connections are tight and weatherproofed.
• تنظيف: If necessary, gently clean the fiberglass elements with mild soap and water to remove dirt or grime. Avoid abrasive cleaners.

6. استكشاف الأخطاء وإصلاحها

If you experience issues with your CHA-250HD antenna, consider the following common problems and solutions:

• نسبة الموجة المرتدة العالية:
  • Check coaxial cable for damage or shorts.
  • Ensure all antenna connections are tight.
  • Verify the antenna is clear of nearby metal objects or structures.
  • Confirm the antenna is mounted vertically and not hanging more than 20 degrees from vertical.
• ضعف الاستقبال/الإرسال:
  • Check all cable connections from the antenna to the transceiver.
  • Ensure your transceiver is set to the correct frequency and mode.
  • Consider local noise sources or propagation conditions.

7. المواصفات

8. الضمان والدعم

للحصول على معلومات الضمان أو الدعم الفني، يرجى الرجوع إلى الموقع الرسمي للشركة المصنعة webالموقع الإلكتروني أو تواصل مع قسم خدمة العملاء. احتفظ بإيصال الشراء لطلبات الضمان.