D149H181 Ed.08
أكو-D14918
ال أكو-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
تحذيرات
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
وصف
- LED كوم
- مفتاح التسجيل
- EXTERNAL POWER CONNECTOR
- READ KEY
- الصمام على
- CONNECTOR CABLE
التوافق
Refer to the instruction manual of your equipment on its compatibility with the أكو-D14918 مفتاح البرمجة.
Connecting incompatible devices can permanently damage the key.
الأسلاك
- مهم: Pay attention to the orientation of the connector.
- أكو-80018
(خياري) - أكو-D14918
مزود الطاقة
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (أكو-80018 or equivalent).
عملية
مهم: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the كوم led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the كوم led starts flashing quickly.
When recording is complete the controller will reset.
الصمام على
Steady or flashing: Indicates that the key is connected to the controller.
LED كوم
ثابت: Indicates an error in the transmission/reception of data
وميض سريع: Indicates transmission/reception of data in progress. At the end of the transmission LED كوم سوف يتم إيقاف تشغيله.
وميض بطيء: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
ملحوظة: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
مهم: أبداً disconnect the programming key during data transmission.
المواصفات الفنية
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
العرض المجلدtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
المواصفات البيئية:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
شركة أكو الكتروميكانيكا المحدودة
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España
35D149181 REV.07 2025
نحن نحتفظ بالحق في توفير المواد التي قد تختلف قليلاً عن تلك الموضحة في أوراقنا الفنية.
المعلومات المحدثة متاحة على موقعنا webموقع.
المستندات / الموارد
 |
AKO D14918 Programming Key [بي دي اف] دليل التعليمات AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |