W2062C Mini Digital Humidity Sensor Controller

1. المقدمة

The W2062C is an intelligent high-precision digital humidity controller designed for various humidity control applications. It features a dual display for current and set humidity, and supports DC 12V or 24V power input with a 10A relay output. This manual provides essential information for the safe and effective operation of your device.

2. معلومات السلامة

• تأكد من مستوى مصدر الطاقة الصحيحtage (DC 12V or 24V) is used to avoid damage to the device.
• For AC 110V-220V applications, a suitable transformer is required.
• Always ensure wiring is correct, especially for 10A relays and high power loads, to prevent electrical hazards.
• Do not expose the device or sensor to extreme temperatures or humidity outside its specified operating range.
• أبقِ الجهاز بعيداً عن الماء والمواد المسببة للتآكل.
• يجب أن يتم التركيب بواسطة فنيين مؤهلين إذا كنت غير متأكد من التوصيلات الكهربائية.

3. محتويات العبوة

تتضمن الحزمة عادةً ما يلي:

• 1 x W2062C Digital Humidity Controller
• 1 x Humidity Resistance Sensor Probe with 1.5m cable

Note: Actual contents may vary based on your specific purchase.

4. المواصفات

5. انتهى المنتجview

The W2062C controller features a dual digital display and two control buttons:

• عرض: The upper (red) display shows the current humidity, and the lower (blue) display shows the set humidity.
• أزرار: 'SET' and 'ENT' (Enter) buttons are used for setting parameters.

6. الإعداد

6.1 تعليمات الأسلاك

Connect the power supply and the load to the controller as shown in the wiring diagram. Ensure all connections are secure and correct, especially for high power loads connected to the 10A relay.

• مدخلات الطاقة: Connect your DC 12V or 24V power source to the designated input terminals.
• اتصال التحميل: Connect your dehumidifier or humidifier (load) to the relay output terminals.

7. تعليمات التشغيل

7.1 ضبط الرطوبة المطلوبة

1. The upper red display shows the current humidity, and the lower blue display shows the set humidity.
2. To set the desired humidity, press the 'SET' button and then use the '+' (STG) or '-' (ENT) buttons to adjust the value.
3. After setting, wait for 3 seconds for the controller to automatically confirm and save the setting.
4. The controller will then automatically energize the relay according to your set humidity parameters.

7.2 Advanced Parameter Settings (P0-P8)

To access the main menu for advanced settings:

1. Press and hold the 'SET' button for 5 seconds.
2. Use the '+' (STG) or '-' (ENT) buttons to navigate through parameters P0-P8.
3. To adjust a specific parameter (e.g., P0), press the 'SET' button and '+' (STG) or '-' (ENT) simultaneously.
4. Adjust the value as needed, then press 'OK' (likely 'ENT' button after adjustment) to confirm.
5. Once confirmed, the controller will save the new parameter settings.

8. الصيانة

• Keep the controller and sensor clean and dry.
• Avoid exposing the sensor to direct water spray or extreme dust.
• Regularly check wiring connections for tightness and signs of wear.
• لا تحاول تفكيك الجهاز أو إصلاحه بنفسك، لأن ذلك قد يبطل الضمان ويشكل مخاطر على السلامة.

9. استكشاف الأخطاء وإصلاحها

10 نصائح المستخدم

• When setting parameters, ensure you wait the full 3 seconds for the changes to be saved automatically.
• Always double-check your wiring, especially the polarity for DC inputs, to prevent damage.

11. الضمان والدعم

للحصول على معلومات مفصلة حول الضمان ودعم إضافي، يرجى الرجوع إلى دليل المستخدم الرسمي بصيغة PDF المتوفر على الرابط التالي: W2062C User Manual (PDF).