SINGCALL APE80 Wireless Signal Ampدليل مستخدم مكبر الصوت

1. انتهى المنتجview

The SINGCALL APE80 is a wireless signal amplifier designed to extend the receiving distance of a calling system. It acts as a repeater, ensuring that signals from call buttons (pagers) reach the receivers effectively, especially in larger areas or environments with signal obstructions. The device can be configured to transmit signals from all connected call buttons or only from specific registered ones.

2. مواصفات المنتج

The APE80 amplifier holds CE, FCC, and RoHS certifications.

3. هيكل المنتج ومكوناته

The APE80 signal amplifier features a user-friendly design with clearly identifiable components for easy setup and operation.

• Sending Antenna: يرسل ampإشارات مضحكة.
• هوائي الاستقبال: Receives signals from call buttons.
• Initialize Light: Indicates initialization status.
• Mode Light: Indicates the current transmitting mode.
• Registration Light: Indicates registration status.
• Receiving Light: Illuminates when a signal is being received.
• زر الانارة: يشير إلى أن الجهاز قيد التشغيل.
• Transmitting Light: Illuminates when a signal is being transmitted.
• قابس الطاقة: Connection point for the power adapter.
• Signal Strength Testing Light: Provides visual feedback on signal strength.
• Function Buttons (Call, Initialize, Mode, Register): Used for device configuration and operation.
• Pressing Key: General term for the operational buttons.
• موقف هوك: Designated area for mounting the device.
• Supply Hub: منفذ إدخال الطاقة.

4. تعليمات الإعداد

4.1. توصيل الطاقة

1. First, electrify the power adapter by plugging it into a suitable power outlet.
2. Then, connect the power adapter to the 'Supply hub' (power plug) on the APE80 amplifier. The Power light should illuminate.

4.2. ضبط الهوائي

1. Draw out both antennas from the ampمكبر.
2. Adjust the antennas so that the angle between each antenna and the ground is approximately 45 degrees (upward).
3. The optimal length of the antennas may vary depending on the environment. Please check and adjust the length during installation for the best performance.

4.3. Initializing the Ampالقمامة

1. Press and hold the 'Initialize' key for approximately one second. The Initialize light will turn on.
2. Release the key and wait. The initialization process is complete when the Initialize light turns off.

4.4. Selecting the Installation Position

Proper placement is crucial for optimal signal amplification. Consider the following methods:

Method A: Intermediate Position

1. ضع amplifier in an intermediate position between the receiver and the farthest call button.
2. Press the farthest call button.
3. If the receiver successfully receives the signal, fix the amplifier in that position.
4. If the receiver does not receive the signal, hold the registered call button and slowly move the amplifier from the receiver towards the farthest call button, continuously pressing the call button until the receiver receives the signal. This is the ideal position to fix the ampمكبر.

Method B: Using the 'Call' Key

1. Register the 'Call' key of the amplifier into the receiver (refer to the receiver's manual for registration instructions).
2. حرك amplifier from the receiver towards the farthest call button, continuously pressing the 'Call' key on the ampمكبر.
3. The best location for the amplifier is the point where the receiver *stops* receiving the signal from the amplifier. If the area where the receiver cannot receive the signal is known, that location is the best place to fix the ampمكبر.

Special Note: If another amplifier is already installed, ensure it is turned OFF when registering new pagers or changing pager numbers to avoid interference.

5. تعليمات التشغيل

5.1. تسجيل أزرار الاتصال

ال amplifier has a capacity for up to 300 call buttons.

1. Press and hold the 'Register' key for approximately one second. The Registration light will turn on.
2. While the Registration light is on, press the call button that you wish to register.
3. If the Registration light blinks, the registration is successful.
4. If the call button was already registered, the Registration light will not blink.
5. To exit registration mode, press and hold the 'Register' key for approximately one second until the Registration light turns off.

5.2. Signal Transmitting Mode Setting

ال amplifier can operate in two signal transmitting modes:

Mode 1: Transmitting Signals of All Call Buttons

1. Ensure the Mode indicator light is ON.
2. Press and hold the 'Mode' key for approximately one second.
3. Release the key when the Mode light turns OFF. In this mode, the amplifier will transmit signals from all call buttons in use.

Mode 2: Transmitting Signals of Registered Call Buttons Only

1. Ensure the Mode indicator light is OFF.
2. Press and hold the 'Mode' key for approximately one second.
3. Release the key when the Mode light turns OFF. In this mode, the amplifier will only transmit signals from call buttons that have been specifically registered to it.

5.3. حالة ضوء المؤشر

• تم التشغيل: Red lights flashing.
• Receiving Signal: Yellow lights flashing.
• Transmitting Signal: Green lights flashing.

6. الصيانة

• Keep the device dry and avoid exposure to moisture to prevent circuit oxidation.
• نظّف الجزء الخارجي بقطعة قماش ناعمة وجافة. تجنّب استخدام مواد كيميائية قاسية أو منظفات كاشطة.
• Do not attempt to disassemble the product yourself. Unauthorized disassembly may cause damage and void the warranty.

7. استكشاف الأخطاء وإصلاحها

• لا يوجد إشارة Ampالتصريح:
  • Ensure the power adapter is properly connected and the Power light is on.
  • Verify that the antennas are correctly extended and angled at 45 degrees.
  • Re-evaluate the installation position using Method A or B described in Section 4.4.
  • Check for potential interference sources (see Section 8.1).
• Registration Light Not Blinking: If the registration light does not blink after pressing a call button, it indicates that the call button has already been registered.
• Abnormal Device Behavior: If you encounter any abnormal behavior or malfunction, do not attempt to repair the device yourself. Contact customer service engineers for assistance.
• Reduced Receiving Distance: The receiving distance can be influenced by weather conditions. Extreme weather may temporarily reduce performance.

8. Cautions and Safety Information

8.1. Interference Sources

To ensure optimal performance and prevent interference, keep the wireless calling products away from the following:

• محطات أساسية للمعدات المتنقلة.
• الثلاجات ومكيفات الهواء وغيرها من الأجهزة الكهربائية ذات الطاقة العالية.
• أجهزة الموجات فوق الصوتية الكبيرة في المستشفيات.

8.2. إرشادات السلامة العامة

• To avoid static electricity, it is recommended to install the amplifier on a physical wall and ensure no part of the human body comes into contact with the device during operation.
• Always use the original power adapter provided with the device. Using a non-original adapter may seriously affect product performance and could lead to damage, for which the user will be responsible.
• Ensure the antennas are positioned at a 45-degree angle and do not touch any other objects to maintain signal integrity.

9 نصائح المستخدم

لم تتوفر أي نصائح محددة للمستخدم من المراجع المقدمةviewمحتوى الأسئلة والأجوبة.

10. الضمان والدعم

The SINGCALL APE80 Wireless Signal Amplifier comes with a 1-month replacement warranty and 12 months of maintenance support. In case of any issues or abnormal findings, please contact our customer service engineers for assistance. Do not attempt to repair or disassemble the product yourself, as this may void your warranty.

For further details or to download the official user manual in PDF format, please refer to the following link: SINGCALL APE80 User Manual (PDF)