GODIYMODULES Dual Channel Receiver Signal Converter (Model B0FBVDF3DF) User Manual

1. المقدمة

This manual provides detailed instructions for the installation, operation, and maintenance of the GODIYMODULES Dual Channel Receiver Signal Converter, Model B0FBVDF3DF. This device is designed to convert PWM signals from an RC receiver into voltage signals for controlling servos and various DC motor equipment. It features high-precision conversion and supports a wide range of applications, including RC tanks, crawlers, and battery-powered vehicles.

2. الميزات الرئيسية

• Dual channel PWM to voltage signal conversion.
• High precision signal conversion for stable servo and DC motor drive.
• حجم التشغيل على نطاق واسعtage range: 7-24V (recommended 12V).
• يدعم مستويات صوت متعددةtage output adjustments to match different motor specifications.
• Suitable for RC crawlers, tanks, and other model applications.

3. المواصفات

4. محتويات العبوة

تتضمن الحزمة:

• 1 x GODIYMODULES Dual Channel Receiver Signal Converter (Model B0FBVDF3DF)

5. الإعداد والأسلاك

Careful wiring is crucial for proper operation. Refer to the diagram below for connection details.

Figure 5.1: Wiring Diagram and Pin Definitions

تعرض هذه الصورة الجزء العلوي view of the converter board with all terminal blocks and pin labels. On the right side, a text overlay defines each pin: VCC (power positive 7-14V, suggested 12V), GND (power ground/PWM negative pole), 5V (external power supply 5V-100mA), P1/P2 (servo receiver PWM signal input), OT1/OT2 (voltage signal to motor speed, 1000µs~1500µs to 4.2V-0V, 1500µs~2000µs to 0V-4.2V), VH1/VH2 (direction signal, 1000µs~1500µs output 5V, 1500µs~2000µs output 0V). It also notes that P1-OT1-VH1 and P2-OT2-VH2 have the same functionality.

5.1. تعريفات الدبوس

• بطاقة الائتمان: Power positive input. Connect to a 7-14V DC power supply. 12V is recommended for optimal performance.
• أرض الواقع: Power ground and PWM negative pole. Connect to the negative terminal of your power supply and the ground of your PWM source.
• 5V: This pin can be used as an external 5V power supply output, providing up to 100mA. Do not exceed this current limit.
• P1، P2: Servo receiver PWM signal input. Connect these to the PWM output channels of your RC receiver. P1 corresponds to channel 1, P2 to channel 2.
• OT1, OT2: المجلدtage signal output for motor speed control.
  • PWM input 1000µs to 1500µs: Output voltage ranges from 4.2V down to 0V.
  • PWM input 1500µs to 2000µs: Output voltage ranges from 0V up to 4.2V.
• VH1, VH2: Direction signal output.
  • PWM input 1000µs to 1500µs: Output is 5V.
  • PWM input 1500µs to 2000µs: Output is 0V.

Note: Both channel groups (P1-OT1-VH1 and P2-OT2-VH2) operate with identical functionality.

5.2. إجراء التوصيل

1. تأكد من فصل جميع مصادر الطاقة قبل إجراء أي توصيلات.
2. Connect the positive lead of your 7-14V DC power supply to the بطاقة في سي سي صالة.
3. Connect the negative lead of your power supply to the أرضي صالة.
4. Connect the PWM signal output from your RC receiver to the P1 و P2 محطات الإدخال.
5. قم بتوصيل OT1 و OT2 outputs to the motor speed control inputs of your DC motor driver or servo.
6. قم بتوصيل في اتش 1 و في اتش 2 outputs to the direction control inputs of your DC motor driver or other relevant components.
7. Double-check all connections for correct polarity and secure fit.

6. تعليمات التشغيل

Once properly wired, the converter operates automatically based on the incoming PWM signals from your RC receiver.

• تشغيل الطاقة: Apply power to the VCC and GND terminals. The device will power up.
• مدخل PWM: The converter continuously monitors the PWM signals on P1 and P2.
• المجلدtage Output (OT1/OT2): الناتج المجلدtage on OT1 and OT2 will vary proportionally to the PWM pulse width, controlling the speed of connected motors. A pulse width of 1500µs typically corresponds to 0V output (stop), while 1000µs and 2000µs correspond to maximum voltage in opposite directions (4.2V).
• Direction Output (VH1/VH2): The VH1 and VH2 outputs provide a 5V or 0V signal to indicate direction, based on the PWM pulse width. This is useful for motor drivers that require a separate direction input.

Ensure your RC transmitter is calibrated correctly to provide the expected PWM pulse widths for desired motor speed and direction control.

7. الصيانة

The GODIYMODULES Dual Channel Receiver Signal Converter is designed for reliable operation with minimal maintenance.

• تنظيف: Keep the board clean and free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning. Avoid using liquids or solvents.
• تقتيش: قم بفحص جميع توصيلات الأسلاك بشكل دوري للتأكد من أنها آمنة وخالية من التآكل أو التلف.
• بيئة: Operate the device within its specified temperature and humidity ranges to prevent damage. Avoid exposure to extreme temperatures or direct sunlight.

8. استكشاف الأخطاء وإصلاحها

If you encounter issues with your signal converter, refer to the following troubleshooting guide:

9. معلومات الضمان

GODIYMODULES products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the purchase documentation or contact your retailer. Typically, a limited warranty covers manufacturing defects for a period from the date of purchase.

لا يغطي هذا الضمان الأضرار الناجمة عن:

• التركيب أو التوصيل غير الصحيح.
• سوء الاستخدام أو الإساءة أو الإهمال.
• العمل خارج نطاق الظروف البيئية المحددة.
• تعديلات أو إصلاحات غير مصرح بها.
• Accidents or natural disasters.

10. دعم العملاء

If you require further assistance or have questions not covered in this manual, please contact GODIYMODULES customer support through your retailer or the official GODIYMODULES website. Please have your product model number (B0FBVDF3DF) and purchase information ready when contacting support.

للحصول على الموارد الإلكترونية والأسئلة الشائعة، تفضل بزيارة: GODIYMODULES Store on Amazon