Kaleinavi DC Motor Speed Controller with Remote Control (Model 002915) User Manual

1. المقدمة

This manual provides detailed instructions for the Kaleinavi DC Motor Speed Controller with Remote Control, Model 002915. This device is designed for stepless speed control and forward/reverse rotation of DC motors, operating at 12V or 24V. Please read this manual thoroughly before installation and operation to ensure proper use and longevity of the product.

2. محتويات العبوة

• 1 x DC Motor Speed Controller Receiver
• 1 x Remote Control (with battery installed)

3. المواصفات الفنية

4. انتهى المنتجview

The Kaleinavi DC Motor Speed Controller consists of a receiver unit and a wireless remote control. The receiver unit connects to your DC power source and motor, while the remote control allows for wireless operation.

4.1. المكونات

Figure 1: DC Motor Speed Controller Receiver and Remote Control.

This image displays the Kaleinavi DC Motor Speed Controller receiver board alongside its white wireless remote control. The receiver board features terminal blocks for power input and motor connection, along with various electronic components. The remote control has four gray buttons labeled ON/OFF, REVERSE, SPEED UP, and SPEED DOWN.

4.2. وظائف أزرار جهاز التحكم عن بُعد

• A (ON/OFF): Toggles the motor power on or off.
• B (REVERSE): يغير اتجاه دوران المحرك.
• C (SPEED UP): Increases the motor speed.
• D (SPEED DOWN): Decreases the motor speed.

5. الإعداد والتثبيت

Follow these steps to properly set up your DC Motor Speed Controller.

5.1. Identify Components and Connections

Figure 2: Receiver board with labeled input, output, and jumper for voltagهـ الاختيار.

This image shows the circuit board of the DC motor speed controller with key components labeled. It highlights the "learn button", the "Jumper for 12/24V change voltage", "DC Input" terminals (+ and -), and "Connect Motor" terminals (+ and -). Dimensions of 50mm by 70mm are also indicated.

5.2. المجلدtagهـ الاختيار

The controller supports both 12V and 24V DC operation. Select the appropriate voltage using the jumper on the receiver board. Ensure the jumper setting matches your power supply and motor voltage.

• Locate the jumper labeled "Jumper for 12/24V change voltage" on the circuit board (refer to Figure 2).
• Adjust the jumper to the desired voltage setting (12V or 24V).

5.3. توصيلات الأسلاك

الشكل 3: مثالample wiring of the controller to a DC motor and power source.

This image illustrates a complete setup, showing the Kaleinavi DC Motor Speed Controller receiver board connected to a DC motor and a power source. The remote control is also visible, demonstrating the full system. Red and black wires are used for connections, indicating positive and negative terminals.

1. توصيل مدخلات الطاقة: Connect your DC 12V or 24V power supply to the "DC Input" terminals on the receiver board. Ensure correct polarity (+ to + and - to -).
2. توصيل المحرك: Connect your DC motor to the "Connect Motor" terminals on the receiver board. The polarity here will determine the initial direction of rotation.
3. التحقق من الاتصالات: Double-check all wiring to ensure secure and correct connections before applying power.

ملحوظة: It is recommended to use motors within 8A for 12V systems and within 5A for 24V systems to prevent overloading the controller.

6. تعليمات التشغيل

Once the controller is wired and powered, you can operate the motor using the remote control.

6.1. التشغيل الأساسي

• تشغيل/إيقاف الطاقة: اضغط على ⏻ (ON/OFF) button to start or stop the motor.
• غير الاتجاه: اضغط على ↻ (REVERSE) button to reverse the motor's rotation direction.
• زيادة السرعة: اضغط على + (SPEED UP) button to increase the motor's speed.
• سرعة انخفاض: اضغط على - (SPEED DOWN) button to decrease the motor's speed.

6.2. Speed Control Gears

The product features five distinct speed control gears. When the motor is at its full speed (100%), the gears correspond to the following percentagالعربية:

• الترس الأول: 20% of full speed
• الترس الثاني: 40% of full speed
• الترس الثالث: 60% of full speed
• الترس الرابع: 80% of full speed
• الترس الخامس: 100% of full speed

على سبيل المثالample, if your motor's maximum speed is 100 RPM, the first gear will operate at 20 RPM, the second at 40 RPM, and so on, up to 100 RPM at the fifth gear.

7. الصيانة

The Kaleinavi DC Motor Speed Controller is designed for low maintenance. Keep the unit clean and free from dust and moisture. Avoid exposing the device to extreme temperatures or direct sunlight. Ensure all connections remain secure.

8. استكشاف الأخطاء وإصلاحها

• المحرك لا يستجيب:
  • Check power supply connections to the receiver board.
  • Verify motor connections for correct polarity and secure contact.
  • تأكد من أن بطارية جهاز التحكم عن بعد تعمل بشكل صحيح.
  • تأكيد المجلدtage jumper setting matches your power supply.
• Motor runs at incorrect speed or direction:
  • Use the SPEED UP/DOWN buttons to adjust.
  • Press the REVERSE button to change direction.
  • Ensure the motor is not overloaded beyond recommended current limits (8A for 12V, 5A for 24V).
• نطاق تحكم عن بعد مخفّض:
  • تأكد من عدم وجود عوائق كبيرة بين جهاز التحكم عن بعد وجهاز الاستقبال.
  • Check for sources of radio frequency interference.
  • استبدل بطارية جهاز التحكم عن بعد إذا لزم الأمر.

9. الضمان والدعم

This product comes with a one-year warranty from the date of purchase. For warranty claims or technical support, please contact Kaleinavi customer service through your retailer or the official Kaleinavi store page.

لمزيد من المساعدة، يرجى زيارة Kaleinavi Store.