AIXZ AIC45 45A Plasma Cutter Instruction Manual

1. المقدمة

This manual provides essential information for the safe and effective operation, setup, and maintenance of your AIXZ AIC45 45A Plasma Cutter. Please read this manual thoroughly before using the equipment to ensure proper function and to prevent injury or damage.

The AIXZ AIC45 is a robust 45A plasma cutting machine designed for precise and efficient metal cutting. It incorporates advanced IGBT inverter technology and a non-HF pilot arc for reliable performance across various metal types.

Image 1.1: AIXZ AIC45 Plasma Cutter in operation.

2. معلومات السلامة

WARNING: Plasma cutting can be dangerous. Always follow safety precautions to prevent serious injury or death.

• السلامة الكهربائية: Ensure the machine is properly grounded. Do not operate in wet conditions. Always disconnect power before performing maintenance or changing consumables.
• حماية العين والوجه: Always wear a welding helmet with appropriate shade settings to protect your eyes and face from intense light and sparks.
• حماية الجسم: ارتدِ ملابس مقاومة للهب، وقفازات متينة، وأحذية واقية. تجنب الملابس الفضفاضة.
• تهوية: Operate in a well-ventilated area to avoid inhaling fumes and gases produced during cutting.
• مخاطر الحرائق: Keep flammable materials away from the cutting area. Have a fire extinguisher readily available. Sparks and hot metal can cause fires.
• منطقة العمل: حافظ على نظافة مكان العمل وخلوه من الفوضى. تأكد من ثبات قدميك.
• الأطفال والمتفرجون: أبقِ الأطفال والأفراد غير المصرح لهم بعيداً عن منطقة التشغيل.
• Machine Overload: Do not exceed the machine's rated duty cycle to prevent overheating and damage.

3. محتويات العبوة

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact AIXZGLOBAL customer service.

• AIXZ AIC45 Plasma Cutter Machine
• XT45 Non-HF Cutting Torch
• الأرض Clamp
• Air Filter and Pressure Regulator Assembly
• خرطوم الهواء
• XT45 Consumables (Nozzles, Electrodes, etc.)

Image 3.1: Included plasma cutter equipment components.

4. مواصفات المنتج

• تكنولوجيا عاكس IGBT: The AIC45 utilizes stable and mature IGBT inverter technology, providing a DC output current of 20-30A at 50/60Hz. It features a 60% duty cycle and an LCD digital display for easy monitoring and control of voltagه والإعدادات الحالية.
• بداية غير عالية التردد (غير عالية التردد): This plasma cutter employs a low-frequency start mechanism, which results in reduced electromagnetic interference. This design facilitates easier arc initiation, improves cutting success rates, and minimizes interference with other electrical equipment, contributing to a safer working environment.


Image 4.1: Non-HF technology benefits.

• Non-Touch Pilot Arc: The non-touch pilot arc technology allows for cutting without direct contact between the torch and the metal workpiece. This feature is particularly effective for cutting rough, painted, or rusty surfaces, producing cleaner cuts with minimal slag and extending the lifespan of consumables.


Image 4.2: Non-touch pilot arc in action.

• Optimized Cutting Capability: The AIC45 is capable of achieving a clean cut thickness of 10mm and a maximum separation cut thickness of 16mm. It is suitable for cutting various metallic materials, including stainless steel, carbon steel, aluminum, copper, and titanium, offering fast cutting speeds and smooth cut surfaces.


Image 4.3: Cutting thickness capabilities.

• Integrated Air Filter Regulator: The machine includes an air filter and pressure regulator to ensure a clean and consistent air supply to the torch, which is crucial for optimal cutting performance and consumable longevity.


Image 4.4: Air filter regulator detail.

• تصميم خفيف الوزن ومحمول: Weighing approximately 5 kg (11.24 lbs) and with compact dimensions, the AIC45 is designed for easy transport and storage, making it suitable for various work environments.


Image 4.5: Dimensions and weight for portability.

• High Heat Dissipation: Equipped with efficient fan cooling, the machine ensures high heat dissipation, contributing to stable operation and extended component life.


Image 4.6: High heat dissipation system.

• 2T/4T Switch: The control panel includes a 2T/4T switch. In 2T (Two-Touch) mode, the arc starts when the trigger is pressed and stops when released. In 4T (Four-Touch) mode, the arc starts with a brief press and release, and stops with another brief press and release, allowing for longer cuts without continuously holding the trigger.

5. تعليمات الإعداد

Before beginning, ensure the machine is powered off and disconnected from the main power supply.

1. فك التعبئة: قم بإزالة جميع المكونات من العبوة بعناية وافحصها بحثًا عن أي تلف ناتج عن الشحن.
2. Connect Air Filter Regulator: Attach the air filter and pressure regulator assembly to the designated 'AIR IN' port on the rear of the plasma cutter. Ensure a secure, airtight connection.
3. توصيل مصدر الهواء: Connect your air compressor hose to the inlet of the air filter regulator. The air compressor should be capable of providing sufficient airflow and pressure for plasma cutting (refer to specifications).
4. توصيل خط أرضيamp: قم بتثبيت الغطاء الأرضي بشكل آمنamp cable to the positive (+) terminal on the front panel of the plasma cutter. Connect the clamp to the workpiece or a clean, bare metal section of the work table, ensuring good electrical contact.
5. Connect Cutting Torch: Plug the XT45 cutting torch cable into the negative (-) terminal on the front panel. Twist to lock it in place.
6. توصيل الطاقة: Connect the plasma cutter's power cord to a suitable 230V power outlet. Ensure the outlet is properly grounded and can handle the machine's current requirements.
7. Initial Air Pressure Adjustment: Turn on your air compressor. Adjust the air filter regulator to the recommended operating pressure (typically 4.5-5.5 bar or 65-80 PSI for plasma cutting, consult specific torch recommendations if available).

Image 5.1: Front and rear panel connections and controls.

6. تعليمات التشغيل

Always wear appropriate Personal Protective Equipment (PPE) including a welding helmet, gloves, and protective clothing before operating the plasma cutter.

1. تشغيل الطاقة: Flip the main power switch on the rear of the machine to the 'ON' position. The LCD display will illuminate.
2. ضبط التيار: Use the current adjustment knob on the front panel to set the desired cutting amperage. The LCD display will show the selected current. Refer to cutting charts for recommended settings based on material type and thickness.
3. Select 2T/4T Mode: Choose between 2T (Two-Touch) or 4T (Four-Touch) mode using the switch on the control panel, depending on your cutting preference and duration.
4. تحضير قطعة العمل: Ensure the workpiece is clean, dry, and free of rust or paint for optimal cutting. Secure the ground clamp firmly to the workpiece or work table.
5. بدء مسار الطيار: Position the torch nozzle approximately 1-2mm above the starting point of the cut. Press the torch trigger. The pilot arc will ignite without touching the workpiece.
6. ابدأ القطع: Once the pilot arc is established, slowly move the torch across the workpiece, maintaining a consistent standoff distance. The plasma jet will cut through the metal. Adjust cutting speed as needed to achieve a clean cut.
7. Monitor Cut: Observe the molten metal and sparks. A proper cut will show sparks exiting from the bottom of the workpiece. If sparks are spraying upwards, the cutting speed may be too fast or the current too low.
8. End Cut: Release the torch trigger to extinguish the arc. Allow the workpiece to cool before handling.
9. إيقاف التشغيل: After completing your work, turn off the plasma cutter and disconnect it from the power supply.

7. الصيانة

تضمن الصيانة الدورية طول عمر جهاز قطع البلازما الخاص بك وأدائه الأمثل.

• فحص المواد الاستهلاكية: Regularly inspect the torch consumables (nozzle, electrode, shield cup) for wear. Replace them when they show signs of pitting, excessive wear, or damage to maintain cut quality and arc stability.


Image 7.1: XT45 Plasma Cutter Torch components.

• Air Filter Regulator: Periodically check the water trap on the air filter regulator. Drain any accumulated moisture by opening the drain valve at the bottom. Ensure the filter element is clean; replace if heavily contaminated.
• تنظيف: Keep the machine and torch clean. Wipe down the exterior with a dry cloth. Ensure cooling vents are free from dust and debris to prevent overheating.
• فحص الكابلات: Inspect all cables (power, torch, ground) for cuts, abrasions, or damage. Replace any damaged cables immediately.
• تخزين: Store the plasma cutter in a clean, dry environment when not in use.

8. استكشاف الأخطاء وإصلاحها

This section addresses common issues you might encounter with your AIXZ AIC45 plasma cutter.

9. المواصفات

10. الضمان والدعم

AIXZGLOBAL is committed to providing quality products and customer satisfaction. While specific warranty details are not provided in this manual, if you encounter any issues with your AIC45 plasma cutter during operation, or if the machine does not function as expected, please contact our professional customer service team immediately. We are available to assist you with troubleshooting and support.

يرجى الاحتفاظ بإثبات الشراء لأي مطالبات ضمان أو استفسارات دعم.