1. المقدمة
This manual provides detailed instructions for the installation, operation, and maintenance of your Wavtech link2 2-Channel Line Output Converter. Please read this manual thoroughly before attempting installation or operation to ensure proper function and to prevent damage to the unit or connected components. The Wavtech link2 is designed to convert high-level speaker signals from a factory or aftermarket head unit into low-level RCA signals, allowing for the addition of aftermarket amplifiers to your audio system.
2. معلومات السلامة
- افصل دائمًا الطرف السالب لبطارية السيارة قبل البدء في أي عمل كهربائي.
- تأكد من عزل جميع الأسلاك بشكل صحيح وتأمينها لمنع حدوث ماس كهربائي وتلف.
- Do not install the unit in locations where it may be exposed to excessive heat, moisture, or direct sunlight.
- استشر فنيًا متخصصًا في تركيب أنظمة الصوت في السيارة إذا لم تكن متأكدًا من أي جزء من عملية التثبيت.
- Use appropriate fuses for all power connections to protect against electrical surges.
3. محتويات العبوة
تأكد من وجود جميع العناصر في العبوة:
- Wavtech link2 2-Channel Line Output Converter
4. انتهى المنتجview
The Wavtech link2 is a compact and efficient line output converter. Familiarize yourself with its components and connections.
الشكل 4.1: أمام view of the Wavtech link2, showing the Wavtech logo and 'link2' model designation.
الشكل 4.2: قمة view of the Wavtech link2, illustrating the power (PWR), detect (DETECT), power supply (PWR SUPPLY), speaker input (SPK INPUT), clip indicator (CLIP), and gain control (GAIN) sections.
الشكل 4.3: مؤخرة view of the Wavtech link2, displaying the CH1(L) and CH2(R) RCA output connectors.
الشكل 4.4: قمة view of the Wavtech link2, indicating approximate width (2.5 inches) and depth (2.9 inches) dimensions.
الشكل 4.5: جانب view of the Wavtech link2, showing the approximate height dimension (1.1 inches).
5. الإعداد والتثبيت
يُعدّ التركيب الصحيح أمراً بالغ الأهمية للحصول على أفضل أداء. اتبع هذه الخطوات بعناية.
5.1 توصيلات الأسلاك
- Power Supply (PWR SUPPLY):
- أرض الواقع: Connect to a clean, solid chassis ground point in the vehicle. Ensure good metal-to-metal contact.
- + 12 فولت: Connect to a constant +12V power source from the vehicle's battery, fused appropriately (e.g., 1A fuse, not included).
- ريم في: Connect to the remote turn-on output of your head unit (if available). This will turn the link2 on/off with the head unit.
- حركة العين السريعة: Provides a remote turn-on signal for your aftermarket ampمكبر.
- Speaker Input (SPK INPUT): Connect the high-level speaker wires from your factory or aftermarket head unit to these terminals. Ensure correct polarity.
- CH1(L) + / -: Connect to the left channel speaker output wires.
- CH2(R) + / -: Connect to the right channel speaker output wires.
- The link2 accepts up to 40V RMS input.
- Output (OUTPUT): Connect standard RCA cables from the link2's CH1(L) and CH2(R) outputs to the input of your aftermarket ampمكبر.
5.2 DETECT Switch
The DETECT switch manages how the link2 turns on and off.
- على: The link2 will turn on when it detects an audio signal on the speaker inputs. This is suitable for most factory systems that do not provide a remote turn-on wire.
- OFF (DC AUD): The link2 will turn on when it detects a DC offset on the speaker inputs. This is common in some factory systems.
- If using the REM IN terminal for turn-on, the DETECT switch setting is less critical, but it is generally recommended to set it to 'OFF' or 'DC AUD' if a dedicated remote wire is used.
5.3 ضبط المكسب
The GAIN knob controls the output level of the link2. Adjust this to match the input sensitivity of your ampمكبر.
- Start with the GAIN knob fully counter-clockwise (minimum).
- Play a test tone (e.g., 0dB, 1kHz) at about 75% of your head unit's maximum volume.
- Slowly turn the GAIN knob clockwise until the CLIP indicator light just begins to flicker, then back it off slightly until the light remains off. This ensures a clean, unclipped signal to your ampمكبر.
5.4 Load Sense
The link2 features load detect functionality for factory systems that require resistance on the speaker outputs to remain active. This ensures the factory head unit does not shut down or reduce output when connected to the link2.
6. تعليمات التشغيل
Once installed and configured, the Wavtech link2 operates automatically. It will turn on and off with your head unit based on the DETECT switch setting or the remote input. The primary operational aspect is ensuring the gain is set correctly to provide a clean signal to your ampمكبر صوت بدون تشويه.
7. الصيانة
The Wavtech link2 requires minimal maintenance.
- حافظ على الجهاز خالياً من الغبار والأوساخ. استخدم قطعة قماش ناعمة وجافة للتنظيف.
- تأكد من سلامة جميع التوصيلات. افحص الأسلاك دوريًا بحثًا عن أي علامات تآكل أو تآكل.
- تجنب تعريض الوحدة لدرجات الحرارة العالية أو الرطوبة.
8. استكشاف الأخطاء وإصلاحها
If you encounter issues with your Wavtech link2, refer to the following common problems and solutions:
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| لا يوجد مخرج صوتي |
|
|
| الوحدة لا تعمل |
|
|
| صوت مشوه |
|
|
9. المواصفات
- وزن السلعة: 8 أونصات
- أبعاد المنتج: 78.74 x 78.74 x 23.62 inches (Note: These dimensions appear to be incorrect based on product images showing 2.5" x 2.9" x 1.1". Please refer to physical product for accurate measurements.)
- رقم موديل المنتج: link2
- ASIN: B09BB4SRTY
- الشركة المصنعة: وافتيك
- حجم الإدخالtage: Up to 40V RMS (Speaker Level)
- القنوات: 2 قناة
- سمات: Load Detect, Remote Turn-On Output
10. الضمان والدعم
The Wavtech link2 comes with a ضمان المصنع لمدة عام. For warranty claims or technical support, please contact Wavtech customer service or the authorized dealer from whom you purchased the product. Keep your proof of purchase for warranty validation.
For further assistance, visit the Wavtech webالموقع أو استشر الوكيل المحلي المعتمد لديك.