DAKASON 4FT LED Vapor Tight Light Instruction Manual

1. المقدمة

This manual provides detailed instructions for the safe installation, operation, and maintenance of your DAKASON 4FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference.

The DAKASON 4FT LED Vapor Tight Light is a high-efficiency lighting fixture designed for demanding environments. It features adjustable wattage (40W/50W/60W), 0-10V dimming capability (dimmer not included), and an IP65 rating for resistance against water, dust, and harsh conditions.

2. معلومات السلامة

WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all national and local electrical codes.

• افصل الطاقة من المصهر أو قاطع الدائرة قبل التركيب أو الصيانة.
• ضمان حجم العرضtage is compatible with the fixture (100-277V).
• لا تلمس الأسلاك الكهربائية المكشوفة.
• تأكد من أن جميع التوصيلات آمنة ومعزولة بشكل صحيح.
• لا تقم بتعديل التثبيتات.
• ارتدِ معدات الحماية الشخصية المناسبة أثناء التثبيت.
• This fixture is designed for indoor/outdoor use in wet, damp, and dusty areas.

3. محتويات العبوة

تأكد من وجود كافة المكونات قبل البدء في التثبيت:

• 1 x 4FT LED Vapor Tight Lighting Fixture
• 10 x Stainless Steel Clips
• 2 × تصاعد بين قوسين
• 4 x Plastic Wall Plugs
• 4 × مسامير
• 1 x Waterproof Cable Gland

Figure 3.1: Included mounting kit and components.

4. المواصفات

Figure 4.1: IP65 rating details for the vapor tight light.

5. تعليمات التثبيت

This fixture supports surface/wall mount and suspension mount (additional accessories required for suspension). The following steps detail surface/wall mounting.

1. قم بإيقاف تشغيل الطاقة: Before starting, ensure electrical power is turned off at the fuse or circuit breaker box to prevent electric shock.
2. Mark mounting locations: Use the mounting brackets to mark the desired locations for drilling holes on the mounting surface.
3. Install mounting brackets: Drill holes and secure the mounting brackets to the surface using the provided screws and wall plugs.
4. تجهيز الأسلاك: Open the fixture housing. Feed the supply wire (not included) through the waterproof cable gland. Select the desired wattage (40W/50W/60W) using the internal switch.
5. اتصالات الأسلاك: Connect the supply wires to the LED driver according to the wiring diagram.
   • Black (Line) to L
   • White (Neutral) to N
   • Green (Ground) to Gnd
   • Purple (Dim+) and Gray (Dim-) for 0-10V dimming control (if applicable).
   Tighten the external nut on the waterproof cable gland to ensure a water-tight seal.
6. تركيبات التثبيت: Lift the fixture housing and snap it into place on the installed mounting brackets.
7. Secure lens: Position the lens onto the fixture housing and secure it with the stainless steel latches/clips. Ensure the lens is tightly sealed with the housing to maintain the vapor-tight integrity.

Figure 5.1: Hard-wired installation steps and wiring diagram.

6. تعليمات التشغيل

Once installed and wired correctly, the DAKASON LED Vapor Tight Light is ready for operation.

• تشغيل الطاقة: Restore power at the circuit breaker. The light will illuminate.
• واتtagاختيار ه: The fixture has a selectable wattage switch (40W/50W/60W) located inside the housing. Adjust this switch قبل sealing the fixture and restoring power to set the desired light output.
  

  Figure 6.1: Internal wattagمفتاح الاختيار ه.
• وظيفة التعتيم: If connected to a compatible 0-10V dimmer switch (not included), the light output can be adjusted from 0% to 100%.

  Video 6.1: Demonstration of 0-10V dimming capability in a warehouse setting.

7. الصيانة

The DAKASON LED Vapor Tight Light is designed for minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

• تنظيف: نظف الجزء الخارجي من الجهاز بشكل دوري بقطعة قماش ناعمة.amp cloth. Do not use abrasive cleaners or solvents, as these can damage the polycarbonate housing and lens. Ensure power is off before cleaning.
• تقتيش: Regularly inspect the fixture for any signs of damage, loose connections, or wear. Pay attention to the waterproof cable gland and stainless steel clips to ensure the seal remains intact.
• لا توجد أجزاء قابلة للصيانة بواسطة المستخدم: There are no user-serviceable parts inside the fixture. Do not attempt to open or repair the LED driver or LED chips. Contact qualified personnel for any repairs.

8. استكشاف الأخطاء وإصلاحها

If you experience issues with your DAKASON LED Vapor Tight Light, refer to the following troubleshooting guide:

If the problem persists after attempting these solutions, please contact DAKASON customer support.

9. الضمان والدعم

DAKASON provides a ضمان لمدة 5 سنوات for this LED Vapor Tight Light, covering defects in materials and workmanship under normal use.

For warranty claims, technical support, or any questions regarding your product, please contact DAKASON customer service through the retailer where the product was purchased or visit the official DAKASON webموقع لمعلومات الاتصال.

Please have your model number (VPD-4A-50KFD) and purchase date available when contacting support.