دايتونا 3 طن لو بروfile جاك الكلمة

مقدمة

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Daytona 3 Ton Low Profile Floor Jack. Designed for heavy-duty use, this jack features a low-profile design to fit under most vehicles and a rapid pump system for quick lifting. Please read this manual thoroughly before use to ensure proper handling and to prevent injury or damage.

Figure 1: The Daytona 3 Ton Low Profile Floor Jack in orange, showcasing its robust design and low-profile الهيكل.

معلومات السلامة

تحذير: قد يؤدي عدم اتباع هذه التعليمات إلى حدوث إصابات خطيرة أو أضرار في الممتلكات.

• Always use jack stands to support the vehicle after lifting. Never rely solely on the floor jack for support.
• Ensure the jack is on a hard, level surface capable of supporting the load. Avoid using on asphalt or soft ground.
• Center the load on the saddle. Off-center loads can cause the jack to tip.
• Do not exceed the rated capacity of 3 tons.
• احرص على إبقاء يديك وقدميك بعيدًا عن الأجزاء المتحركة.
• ارتدِ معدات الحماية الشخصية المناسبة، مثل نظارات السلامة والقفازات.
• Do not modify the jack or use it for purposes other than lifting vehicles.
• Before lowering, ensure all tools and personnel are clear from under the vehicle.

مكونات أكثرview

Familiarize yourself with the main components of your floor jack:

• سرج: The circular pad that contacts the vehicle's lift point. It is rotating and removable to adapt to lift accessories.
• Lift Arm: The main arm that raises and lowers the saddle.
• مقبض: Used for pumping the jack and controlling the lowering mechanism.
• صمام الإصدار: Located at the base of the handle, controls the lowering speed.
• العجلات الأمامية: Fixed wheels at the front of the jack.
• Rear Swivel Casters: Ball bearing casters at the rear for 360° mobility.
• الوحدة الهيدروليكية: Contains the dual piston hydraulic system for rapid lifting.

الشكل 2: من أعلى إلى أسفل view of the Daytona 3 Ton Floor Jack, highlighting the saddle, handle connection, and the "3 TON LOW PROFILE HIGH PERFORMANCE" label.

يثبت

1. فك التعبئة: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. تجميع المقبض: Insert the handle into the handle socket at the rear of the jack. Secure it according to the instructions provided in the separate assembly sheet (if applicable).
3. Purging Air (Bleeding): Before first use, or if the jack has been stored horizontally, it may be necessary to purge air from the hydraulic system.
   • أدر صمام التنفيس عكس اتجاه عقارب الساعة لفتحه بالكامل.
   • Pump the handle rapidly 10-15 times without a load.
   • أدر صمام التحرير في اتجاه عقارب الساعة لإغلاقه.
   • Test the jack's lifting and lowering function. Repeat if necessary.

تعليمات التشغيل

Lifting a Vehicle:

1. إعداد السيارة: أوقف السيارة على سطح صلب ومستوٍ. فعّل فرامل اليد وثبّت العجلات التي ستبقى على الأرض.
2. وضع الرافعة: Locate the vehicle manufacturer's recommended lifting points. Slide the jack under the vehicle, ensuring the saddle is centered directly under the lifting point.


Figure 3: The Daytona 3 Ton Floor Jack correctly positioned under a vehicle's frame, ready for lifting. Note the low profile allowing access.

3. ارفع المركبة: Turn the release valve clockwise until it is firmly closed. Pump the handle up and down to raise the vehicle to the desired height. The dual piston system provides rapid lifting.
4. التثبيت باستخدام حوامل الرفع: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Lowering a Vehicle:

1. الاستعداد للتخفيض: Ensure the area around and under the vehicle is clear of obstructions and personnel.
2. ارفع قليلاً: If the vehicle is on jack stands, position the floor jack under the original lifting point and raise the vehicle slightly to clear the jack stands.
3. إزالة دعامات الرفع: قم بإزالة حوامل الرافعة بعناية.
4. إنزال المركبة: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Do not open the valve too quickly, as this can cause the vehicle to drop rapidly.
5. إزالة جاك: Once the vehicle is fully on the ground, remove the floor jack.

صيانة

• تشحيم: Periodically lubricate all moving parts with light machine oil. Check the wheels and casters for smooth operation.
• السائل الهيدروليكي: Check the hydraulic fluid level every 6 months. To check, lower the jack completely, remove the oil filler plug, and ensure the fluid is level with the bottom of the filler hole. Use only high-quality hydraulic jack oil. Do not use brake fluid or motor oil.
• تنظيف: Keep the jack clean and free of dirt, grease, and debris. This helps prevent corrosion and ensures smooth operation.
• تخزين: Store the jack in a clean, dry place with the ram fully retracted to prevent rust and extend seal life.
• تقتيش: قبل كل استخدام، افحص الرافعة بحثًا عن أي علامات تلف أو تسريب أو تآكل. لا تستخدم رافعة تالفة.

استكشاف الأخطاء وإصلاحها

تحديد

الضمان والدعم

For warranty information or technical support, please refer to the official Daytona webالموقع الإلكتروني أو تواصل مع قسم خدمة العملاء. احتفظ بإيصال الشراء لطلبات الضمان.

الدعم عبر الإنترنت: قم بزيارة Daytona Store on Amazon للحصول على معلومات المنتج وموارد الدعم.