1. انتهى المنتجview
The Daytona 3 Ton Long Reach Low Profile Steel Heavy Duty Floor Jack is engineered for lifting a wide range of vehicles, from low-profile cars to trucks and SUVs. Its design features a long reach and an extra-low profile, allowing access under most performance vehicles. Equipped with dual piston Rapid Pump technology, this jack efficiently lifts most workloads in approximately 3-1/2 pumps.
المميزات الرئيسية:
- Lift height range from 3-1/4 inches to 24-1/4 inches.
- Dual piston hydraulic system for rapid lifting.
- Ball bearing premium rear swivel casters for 360° mobility.
- Rotating, removable jack saddle for quick adaptation to lift accessories.
- Industrial strength powder coat finish for durability.
2. معلومات السلامة
Always prioritize safety when operating any lifting equipment. Failure to follow these instructions may result in serious injury or property damage.
- اقرأ الدليل كاملا: Understand all warnings, cautions, assembly, operating procedures, and maintenance instructions before using this product.
- للاستخدام على سطح صلب ومستوٍ: Operate the floor jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
- استخدم حاملات الرافعة: After lifting the vehicle, always support it immediately with appropriate jack stands. Never rely solely on the floor jack to support a vehicle.
- Do Not Exceed Rated Capacity: This jack has a 3-ton (6,000 lb) capacity. Do not attempt to lift loads heavier than this rating.
- توسيط الحمل: تأكد من أن الحمل متمركز على قاعدة الرافعة. فالأحمال غير المتمركزة قد تسبب عدم الاستقرار.
- ابقي واضحا: Keep hands, feet, and other body parts clear of moving parts and the area under the lifted load.
- Lower Slowly: Always lower the load slowly and in a controlled manner.
- فحص قبل الاستخدام: قبل كل استخدام، افحص الرافعة للتأكد من خلوها من أي تلف أو تسريبات أو أجزاء مفكوكة. لا تستخدمها إذا كانت تالفة.
3. الإعداد
Before first use, ensure the jack is properly assembled and prepared.
- فك التعبئة: Carefully remove the floor jack from its packaging. Inspect for any shipping damage.
- تجميع المقبض: Insert the handle into the handle socket. Secure it according to the specific instructions provided with your jack model, typically involving a set screw or pin.
- Bleeding the Hydraulic System (if necessary): If the jack does not lift properly or feels spongy, air may be trapped in the hydraulic system. To bleed:
- Turn the release valve counter-clockwise one full turn to open it.
- Pump the handle rapidly 10-15 times without a load.
- أدر صمام التحرير في اتجاه عقارب الساعة لإغلاقه.
- Test the jack for proper operation. Repeat if necessary.
4. تعليمات التشغيل
Follow these steps for safe and effective vehicle lifting.
- إعداد السيارة: أوقف السيارة على سطح صلب ومستوٍ. فعّل فرامل اليد وثبّت العجلات التي ستبقى على الأرض.
- وضع الرافعة: Locate the vehicle's manufacturer-recommended lifting points. Slide the floor jack under the vehicle, ensuring the saddle is centered directly under the lifting point.
- ارفع المركبة: Close the release valve by turning the handle clockwise until it is firm. Pump the handle to raise the vehicle to the desired height.
- التثبيت باستخدام حوامل الرفع: Immediately place appropriately rated jack stands under the vehicle's frame or designated support points. Ensure the vehicle is securely resting on the jack stands before performing any work.
- إنزال المركبة: To lower, slowly turn the release valve counter-clockwise. The vehicle will descend. Once fully lowered, remove the jack.
5. الصيانة
Regular maintenance ensures the longevity and safe operation of your floor jack.
- تشحيم: Periodically lubricate all moving parts, pivot points, and casters with light machine oil.
- السائل الهيدروليكي: Check the hydraulic fluid level every three months or as needed. To check, lower the jack completely, remove the oil filler plug, and ensure the fluid is at the correct level (usually just below the filler hole). Use only high-quality hydraulic jack oil.
- تنظيف: Keep the jack clean from dirt, grease, and corrosive materials. Wipe down after each use.
- تخزين: Store the jack in a dry, protected area with the ram fully retracted to prevent corrosion and extend seal life.
6. استكشاف الأخطاء وإصلاحها
راجع هذا القسم للتعرف على المشكلات الشائعة وحلولها.
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| لن يرفع جاك الحمولة. | Release valve open; Air in system; Low hydraulic fluid. | Close release valve; Bleed air from system (see Setup); Add hydraulic fluid. |
| Jack lifts slowly or with difficulty. | Air in system; Low hydraulic fluid; Overload. | Bleed air from system; Add hydraulic fluid; Reduce load (do not exceed capacity). |
| Jack leaks hydraulic fluid. | Loose fittings; Damaged seals. | Tighten fittings; Contact customer support for seal replacement. |
| ينخفض الرافعة تحت الحمل. | Release valve not fully closed; Internal seal damage. | Ensure release valve is fully closed; Contact customer support for repair. |
7. المواصفات
| مواصفة | قيمة |
|---|---|
| ماركة | دايتونا |
| رقم الموديل | 64241 |
| سعة التحميل | 3 طنًا (6,000 رطل) |
| الحد الأدنى للارتفاع | 3.25 بوصة |
| أقصى ارتفاع للرفع | 24.25 بوصة |
| مادة | فُولاَذ |
| نوع خدمة المركبة | عربه نقل |
| لون | البرتقالي |
8. الضمان والدعم
Daytona products are manufactured to high-quality standards. For specific warranty information, please refer to the warranty card included with your product or visit the official Daytona webموقع. احتفظ بإيصال الشراء الخاص بك لمطالبات الضمان.
For technical assistance, parts, or service inquiries, please contact Daytona customer support. Contact information can typically be found on the product packaging or the official brand webموقع.
الموارد المتاحة على الإنترنت: لمزيد من المعلومات والدعم، يمكنك زيارة Daytona Store on Amazon.