دليل مستخدم وحدة تزويد الطاقة Antminer APW7

1. انتهى المنتجview

The Antminer APW7 is a high-efficiency power supply unit (PSU) designed for various ASIC miners, including models like the Antminer S9, L3+, Z9 Mini, D3, and Z15 420K. It serves as an upgrade from previous models, offering enhanced power output and efficiency.

الشكل 1: الجبهة view of the Antminer APW7 Power Supply Unit.

This PSU is equipped with multiple 6-pin PCI-e connectors to support various mining hardware. It features built-in protection mechanisms that automatically shut off the unit in case of circuit malfunction or excessive internal temperature, safeguarding connected miners.

2. المواصفات

3. دليل الإعداد

3.1 فك العبوة والتفتيش

Carefully remove the APW7 PSU from its packaging. Inspect the unit for any signs of physical damage. Ensure all cables and connectors are intact.

الشكل 2: الجانب view showing the specifications label on the PSU.

3.2 توصيل الطاقة

The APW7 PSU supports both 110V and 220V AC input. The maximum output wattage depends on the input voltage:

• ل 1000 واط output, use a 110 فولت-120 فولت power cable (standard 3-prong household plug).
• ل 1800 واط output, use a 220 فولت-240 فولت power cable (requires a specific higher-voltage plug, typically a C13/C14 or C19/C20 connector, not a standard household plug).

Ensure you use the appropriate power cable for your electrical setup to achieve the desired wattage. Connecting the correct power cable to the PSU's input port is crucial.

الشكل 3: العودة view of the PSU showing the power input and cooling fan.

3.3 Connecting to Miner

The APW7 PSU comes with 10 x 6-pin PCI-e connectors. These connectors are used to power your ASIC miner(s). Connect the 6-pin connectors from the PSU to the corresponding power input ports on your miner(s). Ensure each connector is securely seated.

Figure 4: The PSU with its array of 6-pin PCI-e power cables.

For optimal performance and to prevent overloading, adhere to the power requirements of your specific miner models. For example, if using 110V input, it is recommended to connect no more than four miners that draw approximately 235W each, to stay within the 1000W limit.

4. تعليمات التشغيل

4.1 التشغيل

Once all connections are secure, plug the power cable into a suitable electrical outlet. The PSU will power on, and its internal fan will begin operating. The fan is designed to run continuously to ensure proper cooling of the unit.

4.2 مصابيح مؤشر

The PSU and connected miners may feature indicator lights to show their operational status. Refer to your specific miner's manual for detailed information on its indicator lights. Generally, a steady green light indicates a stable power connection and normal operation.

5. الصيانة

Regular maintenance helps ensure the longevity and optimal performance of your APW7 PSU.

• تنظيف: Periodically clean the fan and ventilation grilles to prevent dust buildup, which can impede airflow and lead to overheating. Use compressed air or a soft brush.
• بيئة: Operate the PSU in a well-ventilated area to facilitate efficient heat dissipation. Avoid placing it in enclosed spaces or near heat sources.
• ضوضاء المروحة: The PSU's fan runs continuously and may produce audible noise. This is normal operation. If the fan noise becomes excessively loud or unusual, it may indicate a potential issue requiring inspection.

6. استكشاف الأخطاء وإصلاحها

If you encounter issues with your APW7 PSU, consider the following:

• لا يوجد طاقة:
  • Ensure the power cable is securely connected to both the PSU and the electrical outlet.
  • تأكد من أن مأخذ الكهرباء يعمل بشكل صحيح.
  • Check if the correct voltage power cable is being used for your region (110V or 220V).
• انتاج الطاقة غير كافية:
  • Confirm that you are using a 220V-240V power source and corresponding cable to achieve the full 1800W output. A 110V-120V source will only provide up to 1000W.
  • Ensure the total power draw of connected miners does not exceed the PSU's maximum output for your voltagالإعداد الإلكتروني.
• ارتفاع درجة الحرارة/الإغلاق التلقائي:
  • Check for proper ventilation around the PSU. Clear any obstructions from the fan and vents.
  • Reduce the load on the PSU by disconnecting some miners if the total wattage exceeds recommended limits.
  • Ensure the ambient temperature is within acceptable operating ranges for electronic equipment.
• ضوضاء المروحة المفرطة:
  • While some fan noise is normal, excessive noise might indicate dust buildup or a failing fan. Clean the fan and vents.
  • If the noise persists, contact support for further assistance.

7. الضمان والدعم

For detailed warranty information and technical support, please refer to the official Antminer webالموقع أو تواصل مع خدمة العملاء مباشرةً. احتفظ بإيصال الشراء كإثبات للشراء في حال وجود أي مطالبات بالضمان.