دليل تعليمات طقم تيل فرامل أمامي أصلي من أكورا

1. المقدمة

This instruction manual provides essential information for the proper handling, installation, and maintenance of the Genuine Acura 45022-S0K-A11 Front Brake Pad Set. These brake pads are designed to meet the original equipment manufacturer (OEM) specifications for your Acura vehicle, ensuring optimal braking performance and safety. Please read this manual thoroughly before proceeding with any installation or maintenance.

2. معلومات السلامة

Brake system work is critical for vehicle safety. Improper installation can lead to serious injury or death. It is highly recommended that installation be performed by a qualified automotive technician.

• Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and closed-toe shoes.
• تأكد من تثبيت المركبة بإحكام على حاملات رافعة على سطح مستوٍ قبل البدء بأي عمل. لا تعتمد أبدًا على الرافعة وحدها.
• Allow the brake system to cool down completely before handling components.
• Do not use petroleum-based lubricants on brake components, as they can damage rubber parts.
• Dispose of old brake pads and brake fluid according to local environmental regulations.
• قم بزيارة دليل خدمة سيارتك للتعرف على مواصفات عزم الدوران والإجراءات المحددة.

3. محتويات العبوة

The Genuine Acura 45022-S0K-A11 Front Brake Pad Set typically includes the following components:

• Four (4) Front Brake Pads (two inner, two outer)
• Shims (pre-attached or separate, depending on design)
• Hardware (e.g., clips, pins, if applicable)

Image: Genuine Acura 45022-S0K-A11 Front Brake Pad Set. The image displays four individual brake pads, two with their dark friction material facing up, and two flipped to show the metal backing plates, which include pre-attached shims and small metal clips, indicating a complete set for a vehicle's front axle.

4. إجراءات التثبيت

This section outlines the general steps for replacing front brake pads. Specific procedures may vary by vehicle model. Always refer to your vehicle's factory service manual for detailed instructions.

1. تحضير: Park the vehicle on a level surface, engage the parking brake, and block the rear wheels. Loosen the front wheel lug nuts.
2. الرفع والتأمين: Safely lift the front of the vehicle using a jack and support it securely with jack stands. Remove the front wheels.
3. إزالة الفرجار: Locate the brake caliper. Remove the caliper guide pin bolts. Carefully slide the caliper off the rotor and support it to prevent strain on the brake hose. Do not let the caliper hang by the brake hose.
4. Pad Removal: قم بإزالة وسادات الفرامل القديمة من حامل الفرجار. لاحظ اتجاهها.
5. تنظيف وفحص: Clean the caliper bracket and guide pins. Inspect the brake rotor for wear, scoring, or warping. Replace rotors if necessary. Lubricate caliper guide pins with appropriate brake grease.
6. سحب المكبس: Use a brake caliper piston compression tool to slowly and evenly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads. Open the brake fluid reservoir cap before retracting pistons.
7. تركيب لوحة جديدة: Install the new Acura brake pads into the caliper bracket, ensuring correct orientation (inner and outer pads). Apply a thin layer of brake lubricant to the backing plates of the pads where they contact the caliper and shims, if not pre-applied.
8. إعادة تركيب الفرجار: Carefully slide the caliper back over the new pads and rotor. Reinstall and torque the caliper guide pin bolts to the manufacturer's specifications.
9. الخطوات النهائية: Reinstall the wheels and torque the lug nuts to specifications. Lower the vehicle. Pump the brake pedal several times until it feels firm before driving. Check the brake fluid level and top off if necessary.

5. إجراءات التشغيل والتشغيل

After installing new brake pads, a proper break-in (bedding-in) procedure is crucial for optimal performance and longevity. This process transfers a thin layer of friction material to the rotor surface, ensuring consistent braking and preventing noise.

1. قيادة السيارة بسرعة معتدلة (على سبيل المثال، 30-40 ميلا في الساعة).
2. استخدم الفرامل باعتدال (وليس بقوة) لإبطاء السرعة إلى حوالي ١٠ أميال في الساعة. لا تتوقف تمامًا.
3. كرر هذه العملية حوالي 10-15 مرات، مع مراعاة ترك فترة تهدئة قصيرة بين كل توقف.
4. Avoid hard braking or prolonged braking (e.g., long downhill descents) for the first 200-300 miles after installation.

During the break-in period, you may notice a slight burning smell or reduced braking effectiveness. This is normal. Braking performance will improve as the pads bed in.

6. الصيانة

Regular inspection of your brake pads is essential for safety and performance.

• التفتيش الروتيني: Inspect brake pads for wear during tire rotations or at least every 10,000-15,000 miles.
• الحد الأدنى للسمك: Replace brake pads when the friction material wears down to the minimum recommended thickness (typically 2-3mm, or as indicated by your vehicle's wear indicators).
• سائل الفرامل: Check brake fluid level regularly and ensure it is within the recommended range. Brake fluid should be flushed and replaced according to your vehicle manufacturer's schedule.
• حالة الدوار: Always inspect brake rotors for excessive wear, deep grooves, or cracks when replacing pads. Rotors should be resurfaced or replaced if they are below minimum thickness or show significant damage.

7. استكشاف الأخطاء وإصلاحها

If you experience any issues after brake pad installation, consider the following common problems and solutions:

If troubleshooting steps do not resolve the issue, or if you are unsure, consult a certified automotive technician.

8. المواصفات

Key specifications for the Genuine Acura 45022-S0K-A11 Front Brake Pad Set:

• رقم القطعة: 45022-S0K-A11
• ماركة: أكيورا
• موضع: المحور الأمامي
• وزن السلعة: يبلغ وزن المجموعة حوالي 4.4 رطل
• أبعاد المنتج: تقريبًا 6.5 × 3.27 × 2.52 بوصة (التغليف)
• التقى المواصفات: الشركة المصنعة للمعدات الأصلية

Note: These specifications are based on typical product information and may vary slightly. Always verify compatibility with your specific vehicle model and year.

9. الضمان والدعم

For information regarding the warranty of Genuine Acura parts, please refer to the warranty documentation provided with your purchase or contact an authorized Acura dealership or parts distributor. They can provide details on coverage, terms, and conditions.

For technical support or further assistance, it is recommended to contact your local authorized Acura service center or a certified automotive professional.