بيرماتكس 80328
دليل مستخدم أسمنت مانع التسرب Permatex 80328
الموديل: 80328
مقدمة
The Permatex 80328 Weatherstrip Cement is a specialized adhesive designed to create a durable, watertight seal between automotive weatherstripping and vehicle surfaces. This cement is formulated to resist cracking and peeling, providing a long-lasting bond against drafts and moisture. It is suitable for bonding metal, glass, and rubber components.
معلومات السلامة
WARNING: EXTREMELY FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. VAPOR HARMFUL.
- استخدمه في منطقة جيدة التهوية. تجنب استنشاق الأبخرة.
- يُحفظ بعيداً عن الحرارة والشرر واللهب المكشوف والأسطح الساخنة. ممنوع التدخين.
- ارتدِ معدات الحماية الشخصية المناسبة، بما في ذلك القفازات وحماية العين.
- Do not ingest. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting.
- في حال ملامسة العينين، اشطفهما جيداً بالماء لعدة دقائق. أزل العدسات اللاصقة إن وجدت وكان من السهل إزالتها. استمر في الشطف.
- يحفظ بعيدًا عن متناول الأطفال.
- Store in a cool, dry place. Keep container tightly closed.
الإعداد والتحضير
- تنظيف الأسطح: Ensure all surfaces to be bonded are clean, dry, and free of grease, oil, dirt, or old adhesive residue. Use a suitable cleaner if necessary and allow to dry completely.
- درجة حرارة: For best results, apply the cement at room temperature (between 60°F and 80°F / 15°C and 27°C).
- تهوية: Work in a well-ventilated area to minimize exposure to vapors.
- اختبار الملاءمة: Before applying adhesive, test fit the weatherstrip to ensure proper alignment and fit.
تعليمات التشغيل (التطبيق)
Follow these steps for effective application of Permatex 80328 Weatherstrip Cement:
- Prepare the Tube: Remove the cap and, if sealed, puncture the tube's seal.
- Apply Cement: Apply a thin, even coat of Permatex Weatherstrip Cement to one of the surfaces to be bonded (e.g., the weatherstrip or the vehicle body). The squeeze bottle applicator allows for quick and easy application.
- Wait for Tackiness: Allow the cement to become slightly tacky, typically within 1-2 minutes, before joining the surfaces. This allows some solvents to evaporate, improving bond strength.
- Join Surfaces: Carefully position the weatherstrip onto the prepared surface. Press firmly and evenly along the entire length to ensure good contact.
- آمن في مكانه: If necessary, use clamps or tape to hold the weatherstrip in place while the cement cures.
- وقت المعالجة: Allow the cement to cure completely before exposing it to moisture or stress. Full cure time may vary depending on temperature and humidity, but typically takes 24 hours. Refer to product packaging for specific cure times.
- Clean Excess: Immediately wipe away any excess cement with a clean cloth dampened with mineral spirits or a suitable adhesive remover before it dries.
Image: Permatex 80328 Weatherstrip Cement in its retail packaging. The image displays the product tube and highlights key features such as flexibility, toughness, waterproofing, and bonding capabilities for metal, glass, and rubber.
الصيانة والتخزين
- Cap Tightly: After each use, ensure the cap is securely replaced on the tube to prevent the cement from drying out.
- تخزين: Store the Permatex 80328 Weatherstrip Cement in a cool, dry place, away from direct sunlight and sources of ignition.
- مدة الصلاحية: For optimal performance, use the product within its recommended shelf life. Check the packaging for any expiration dates.
- Clean Applicator: If the applicator tip becomes clogged, clear it with a small wire or pin before attempting to use the product again.
استكشاف الأخطاء وإصلاحها
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| Cement not bonding properly. | Surfaces not clean; insufficient drying time; improper application; low temperature. | Ensure surfaces are thoroughly cleaned and dry. Allow cement to become tacky before joining. Apply at recommended temperatures. Apply an even coat. |
| Cement dries too quickly. | High temperature; low humidity; too thin a coat. | Work in a cooler environment if possible. Apply a slightly thicker, but still even, coat. Work quickly. |
| Cement tube is clogged. | Cement dried in the nozzle. | Clear the nozzle with a small pin or wire. Ensure cap is tightly sealed after each use. |
| Weatherstrip peels off after curing. | Insufficient pressure during application; not enough cure time; surface contamination. | Apply firm, even pressure when joining surfaces. Allow full cure time (24 hours recommended). Re-clean and reapply if contamination is suspected. |
تحديد
- اسم المنتج: Permatex Weatherstrip Cement
- رقم الموديل: 80328
- ماركة: بيرماتكس
- شكل العنصر: Liquid / Cement
- الوزن الصافي: 2.0 fl. oz. (59 ml) / 0.17 Pounds (approx. 2.72 ounces)
- توصية السطح: Window (suitable for metal, glass, rubber)
- المميزات الرئيسية: Flexible, Tough, Waterproof, Bonds Metal, Glass, Rubber
- رمز المنتج العالمي: 079340803282
- رقم قطعة الشركة المصنعة: 80328
- ASIN: B004BT6RL2
الضمان والدعم
Permatex products are manufactured to high-quality standards. For specific warranty information or technical support regarding your Permatex 80328 Weatherstrip Cement, please refer to the official Permatex webالموقع أو تواصل مع خدمة العملاء مباشرةً. احتفظ بإيصال الشراء لأي مطالبات بالضمان.
You can visit the official Permatex store for more information: متجر بيرماتكس على أمازون
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.