Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant User Manual

المنتج انتهىview

The Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant is a high-performance silicone gasket maker designed for high-temperature applications and heavy-duty use. It forms a durable, flexible, and waterproof seal, resisting temperatures from -65°F to 650°F (-54°C to 343°C) intermittently. This product is ideal for creating formed-in-place gaskets or sealing pre-cut gaskets in various automotive and industrial applications.

Image: Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant tube. This image shows the product packaging, a red tube of sealant with the Permatex logo and product name.

معلومات السلامة

Read all safety precautions before use. Do not handle until all safety instructions are understood.

وقاية:

• Contains: Calcium carbonate, iron oxide.
• احصل على تعليمات خاصة قبل الاستخدام.
• استخدام معدات الوقاية الشخصية على النحو المطلوب.

إجابة:

• إذا في العين: شطف بحذر بالماء لعدة دقائق. إزالة العدسات اللاصقة، إذا كانت موجودة وسهلة للقيام. استمر في الشطف. إذا استمر تهيج العين: احصل على المشورة/العناية الطبية.
• إذا كان على الجلد: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse.

تخزين:

• حماية من أشعة الشمس.
• تخزينها في مكان جيد التهوية.
• المتجر مقفل.

تصرف:

• تخلص من المحتويات / الحاوية في محطة التخلص من النفايات المعتمدة.
• يحفظ بعيدًا عن متناول الأطفال.

Image: Back of Permatex 81160 packaging. This image displays the detailed safety warnings, directions for use, and precautionary statements in English and Spanish.

تعليمات التقديم

تحضير:

1. For best results, ensure surfaces are clean and dry.

طلب:

2. Cut the nozzle to the desired bead size (typically 1/16" to 1/4" or 2 to 6mm).
3. Apply a continuous bead of silicone to one surface, ensuring it surrounds all bolt holes.
4. قم بتجميع الأجزاء على الفور بينما يكون السيليكون لا يزال رطبًا.
5. Finger tighten until material begins to squeeze out around the flange.

Curing and Finishing:

5. Allow the sealant to dry for one hour, then tighten to torque specifications.
6. Allow 24 hours for the sealant to fully cure before filling with fluids or returning to service.
7. Replace the cap after use to prevent drying.

NOTE: Not recommended for use on head gaskets or parts in contact with gasoline.

Image: Formed-in-Place Gasket. A hand applies Permatex sealant to an engine component, demonstrating the application process for creating a gasket.

التطبيقات المقترحة

Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant is suitable for a variety of high-temperature and heavy-duty applications, including:

• أغطية الصمامات
• أحواض الزيت
• Timing covers
• مضخات المياه
• Thermostat housings
• أحواض ناقل الحركة

Image: Suggested Applications. This banner image shows various engine components like valve covers and water pumps, highlighting the sealant's intended uses.

تحديد

استكشاف الأخطاء وإصلاحها

إذا واجهت مشكلات أثناء التطبيق أو بعده، ففكر فيما يلي:

• تسرب: Ensure surfaces were thoroughly cleaned and dried before application. Verify that a continuous bead was applied and that parts were assembled while the silicone was still wet. Allow the full 24-hour cure time before exposing to fluids or service.
• ضعف الالتصاق: Surface preparation is critical. Ensure all oil, grease, and old gasket material are removed. The sealant may not adhere properly to contaminated surfaces.
• معالجة المشاكل: Ensure the product was stored correctly and is within its shelf life. Proper ventilation during curing is also important.

For persistent issues, refer to the Permatex webالموقع أو الاتصال بدعم العملاء.

الضمان والدعم

For information regarding product warranty, technical support, or frequently asked questions, please visit the official Permatex webالموقع الإلكتروني أو تواصل مع قسم خدمة العملاء. احتفظ بإيصال الشراء لأي مطالبات بالضمان.